Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > 1995 Wrangler, Extension housing replacement

Join Wrangler Forum Today

Thread: 1995 Wrangler, Extension housing replacement Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-10-2013 01:27 PM
larrythefilmguy Update, jeep is fixed. I froze the slip yolk and it slid through the bushing...

Attachment 333233

Just did a test drive up to 50mph and all is smooth
09-10-2013 11:09 AM
OverkillYJ I would just buy an SYE since it comes with the main shaft for the TC internals. Then obviously you would get a new driveshaft.

Trying to get that thing back together after that type of damage has been done, has fail written all over it. You may get it together, but I have a feeling you will have some nice vibes.
09-09-2013 11:59 AM
reno92 The fact that it went in means something is stopping it from going furthur. It could just mean the dry shaft and dry seal are sticking so try ATF. The other problem could be what I mentioned earlier. Did the slip yoke get damaged when it flew off at 70 mph? Are there burs on the yoke? Run you hand down the shaft with some ATF and see if it's smooth.
09-09-2013 09:05 AM
AllMudd I am not a fan of forcing anything. If you do it could create another issue. The yoke should slide in the housing snug but not be forced in.
09-09-2013 01:20 AM
larrythefilmguy Is it safe to tap the shaft through the bushing? I will put some t fluid on as well..
09-09-2013 12:17 AM
reno92 Did you put a little T fluid on the yoke and around the seal? It needs to be tight to keep from leaking. I'd put the cone on the TC so once you get it in and on the shaft you don't have to pull it off.
09-08-2013 11:31 PM
AllMudd Yea that's not far enough. You can tell it needs to go another 2" or so just by the shinny spot in the yoke.
09-08-2013 10:52 PM
larrythefilmguy This is as far as I can get the slip yolk in. It stops at the bushing. I am trying to figure out if this is normal or do I need to apply force..

Attachment 328857

I need to go another 2 inches or I won't be able to attach to my rear axle
09-08-2013 08:38 PM
reno92 Okay, now I see your photos. So you put a new cone on, I'm assuming it fits flush with the TC housing, you put on new snap rings on the shaft and the end of the cone had the rear seal bushing in already, you added the lock ring and cover. You say the driveshaft stops at the bushing, which is good you don't want it pushing against the bushing, this is your slip yoke. So I'm not sure where the problem is, does the slip yoke not move along the shaft?
09-08-2013 07:55 PM
reno92 I'm trying to picture what you're describing. So you are saying your u-joints broke and your DS slipped out the TC. Did it ruin your TC output tail cone (new extension)?
did you add a new tail cone or do a SYE? If you added a new tail cone and you're trying to slip the old slip yoke in, I would inspect it close. It went flying around at 70 mph, I'd also have your DS checked out as it must have hit a lot of things spinning free at that speed.
09-08-2013 07:44 PM
larrythefilmguy No I did not need a new drive shaft, I am at work at the moment but I installed the new extension housing and it already had a bushing. Once line up the drive shaft it stops at the bushing
09-08-2013 07:37 PM
AllMudd Pics. And did you need a new drive shaft?
09-08-2013 06:46 PM
1995 Wrangler, Extension housing replacement

Hey everyone, I have a 4cyl 95 wrangler, my driveshaft decided to do a combat roll off my transfer at about 70, i found that i wore my u joints out (rookie mistake, should have noticed the vibration) so now I have the new extension housing with a new bushing and my shaft does not slide through, is this normal?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 01:20 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC