Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Flywheel got resurfased

Join Wrangler Forum Today


Thread: Flywheel got resurfased Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-17-2013 08:53 AM
Jerry Bransford Resurfacing the flywheel wasn't recommended but that's definitely not what is causing your problem.
09-17-2013 08:43 AM
mudmagnet63 All I know is the clutch was working fine when I dropped it off. After the resurfacing it didn't. Everything will be new now at no cost to me so no more worries.
09-17-2013 07:07 AM
tailhole
Quote:
Originally Posted by Rubicondon53 View Post

Wow, if you have done a lot of em I'm a bit surprised. I've had nothing but manual transmissions in all of my vehicles dating back to 1970 and all had well over 100k miles on them, only ever had to replace clutches 3 times, and never resurfaced any of the flywheels. Why mill it down when the designers say not to? I'm no rocket scientist, but I do know that once a piece of steel is milled down it looses not only the original mating shape, but also becomes less tolerant of heat.. Then again, if one uses the clutch properly it should never get hot.. The last clutch I replaced was because of a broken PP spring.. I just don't get how clutches are failing as often as they do ? I must be missing something...
I my self isn't doing anything wrong. But collecting 30-80 bucks every time I surface a flywheel
09-17-2013 06:53 AM
C.L. Sounds like maybe the shop put the throwout/pilot bearing in backwards, or used the wrong one? I've heard of that happening; causes the clutch disk to bind up on the shaft before fully engaging the flywheel.

The thing about resurfacing is that the factory puts a VERY slight "dome" on the flywheel. This lets the center section engage a hair before the outer section, which helps with alignment and to prevent shuddering at takeoff. Losing the dome can make it shudder/chatter a bit right at the engagement zone, but won't prevent it from engaging at all.
09-16-2013 10:03 PM
Rubicondon53
Quote:
Originally Posted by tailhole View Post
I have surfaced a lot of them over the past 25 years and have never heard of a problem out of them.
And I'm sure they didn't take 80 off of it. If they had to grind that much off to clean it up, it wasn't working before.
Wow, if you have done a lot of em I'm a bit surprised. I've had nothing but manual transmissions in all of my vehicles dating back to 1970 and all had well over 100k miles on them, only ever had to replace clutches 3 times, and never resurfaced any of the flywheels. Why mill it down when the designers say not to? I'm no rocket scientist, but I do know that once a piece of steel is milled down it looses not only the original mating shape, but also becomes less tolerant of heat.. Then again, if one uses the clutch properly it should never get hot.. The last clutch I replaced was because of a broken PP spring.. I just don't get how clutches are failing as often as they do ? I must be missing something...
09-16-2013 09:28 PM
tailhole I have surfaced a lot of them over the past 25 years and have never heard of a problem out of them.
And I'm sure they didn't take 80 off of it. If they had to grind that much off to clean it up, it wasn't working before.
09-16-2013 10:29 AM
mudmagnet63 I just got off the phone again. The Dealership confirmed to the repair shop that the flywheel is not serviceable. So I'm getting all new guts, it should be done when I fly home on Friday. The boss was out of town when the flywheel was resurfaced and he did not notify the tech of my information on the flywheel. I'm all better now.
09-16-2013 10:16 AM
TJspeed When I replaced my clutch I resurfaced the flywheel and haven't had any issues. That was 7k miles ago
09-16-2013 10:14 AM
mudmagnet63
Quote:
Originally Posted by flflash View Post
I imagine they removed more than .008. .008 isn't much more than the thickness of a sheet of paper. Now if they removed .080 you'll have clutch release issues.

That's what I'm thinking too, someone read their measurements wrong.
09-16-2013 10:12 AM
mudmagnet63 Something is not adding up. The clutch was fine before I pulled it into the shop, I had it replaced because the tranny was out. The guy that runs the shop is a major gearhead and he has done other projects for me with no problems.
09-16-2013 10:05 AM
flflash I imagine they removed more than .008. .008 isn't much more than the thickness of a sheet of paper. Now if they removed .080 you'll have clutch release issues.
09-16-2013 10:02 AM
KBR97 I had mine resurfaced a few years ago when I did the first clutch on my jeep. Never new that it wasn't supposed to be done until I found out afterwards. I haven't had any real problems though. Now and then I get a little shudder from a stand still when the jeep is cold.
09-16-2013 09:52 AM
mudmagnet63 He said they removed.008. That doesn't sound like that would be enough to make it not engage at all. Anyone ever heard of this happening before. The Jeep had 120k pn it when I purchased it so it's possible it has been done before.
09-16-2013 08:43 AM
jherrington At least they aren't trying to make you pay for a new clutch!
09-16-2013 08:39 AM
mudmagnet63
Flywheel got resurfased

The shop that rebuilt my transmission and transfer case had the flywheel resurfaced. Guess what happened.

They put it all back together and it wouldn't move. Just shudder

They called to tell me of the problem and I asked about the flywheel he said that was not the issue. Now they are putting in a new flywheel and another clutch.

I specifically told them not to resurface it and they did it anyway "because it needed it" This is going to get interesting. Last time I use them for anything.

Mud

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:12 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC