Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > help with misfire, sputtering etc

Join Wrangler Forum Today


Thread: help with misfire, sputtering etc Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-01-2012 10:25 AM
Evpjr These code translations courtesy of Haynes Repair Manual, Jeep Wrangler, model years 1987-2003.
09-01-2012 10:22 AM
Evpjr I cn identify your codes; 12 code is battery power to PCM disconnected, 42 code is, An open or shorted condition detected in the Auto-Shutdown Relay circuit. and 55 code is End of Code Output.
08-31-2012 07:33 PM
excj5
Quote:
Originally Posted by beau hunt View Post
undo the wire that run into the cpu and see if their is power steering fluid in it. if so their is a switch or something in ur powersteering pump that when it failes sends powersteering fluid all threw ur electrical
08-31-2012 04:04 PM
beau hunt undo the wire that run into the cpu and see if their is power steering fluid in it. if so their is a switch or something in ur powersteering pump that when it failes sends powersteering fluid all threw ur electrical
04-06-2010 08:43 PM
97tjlex
fixed intermentent jeep misfire

To help i just fixed an intermentant misfire and have some things to help id problem

if obvious items are good such as plugs wires distributer distibuter rotor coil then try this

if engine misfires at an consistant rpm it could be TPS switch located on backside of air intake manifold the electrical sensor has moving parts and could have a bad spot
to test rev engine in neutral to the bad rpm point if misfire then good chance it is TPS, replaced 3 on 97 TJ over past 3 years cost $40 at autozone can replace in 10 minutes
the tach also pinged to the right but the engine did not rev, made me think it was electrical

If the misfire is only noticed when driving, and does not appear to happen at same rpms it could be a crank position sensor That was my problem it had a kinked wire , shorted, it made partial connection and would randomly misfire at various rpms easy to get to, replaced in 5 minutes, i replaced it for $80 from autozone

when this sensor went out the tach would also ping to the right without engine rev

Hope this helps someone
03-15-2010 10:42 AM
mrcarcrazy Personally I wouldn't run it w/o o2 sensors...thats how it decides how much fuel...

The possibilities are endless.

step one in my book would be to fix the obvious things...like the o2 sensors.

find out what the codes mean

97 should be OBD2 - so codes should look like P0171 or something similar.
03-15-2010 10:42 AM
adkjoe I was having trouble with this and It ended up being a terminal on the coil pack was rusty and it was causing cyl. 3 to misfire badly. Cleaned it up with some sand paper changed the plug wires and it stopped sputtering and misfiring. May be a long shot but check out your ignition terminals.
03-15-2010 10:22 AM
xtsniper0 anyone?
03-14-2010 04:36 PM
xtsniper0 forgot to add getting codes 12, 42,55 and gas gauge isnt working
03-14-2010 04:23 PM
xtsniper0
help with misfire, sputtering etc

i am stumped, my jeep was misfirng sputtering about a year back ppl said bad 02 so i disconnected the upstream one, it ran fine with the check engine light on for a like a year, now its doing the same thing even with 02 disconnected, when u hit gas in neutral its fine no missses etc, when u put it into first and start driving it starts doing it misifirng runnign like crap etc,engine has 30 k on rebuild, fuel pump is only a few years old, is there any sensor that monitors trans speeed? im lost the jeep is a 97 tj 2.5 manual , thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:07 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC