Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Can't remove spring bolt!!!!!!

Join Wrangler Forum Today


Thread: Can't remove spring bolt!!!!!! Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-16-2010 04:41 PM
chrisb0108 Rides a lot better too. With the acception of the few things we ran into that held us up, the install is fairly simple. The problems were the pitman arm removal from the tie rod and steering box (remover tool I had sucked), rear front spring removal, rear track bar removal, two broken socket wrenches, a broken universal socket pivet (or whatever its called) & a partridge in a pear tree. This lift install was a first for both of us!
04-16-2010 04:31 PM
chrisb0108 I appreciate all the replies. After multiple hours of trying anything we could think of, I found a heavy duty grinder my dad had given me a while back and it was done in a matter of minutes. Had to grind off both ends of the bolt and pry the spring out of the hanger. 16 yrs will do that i guess...
Got the lift on and so far so good. Will post some before and after pics shortly. Thanks again!!
04-16-2010 06:31 AM
yjtodd I had to cut mine out as well. I had new bolts to install -so no issue.
04-15-2010 09:16 PM
Kohrs93 MY dad and i just had to replaced a broken leaf spring on mine and we tried everything. Then we finally tried using a propane torch. Heat it up for a good minute or so and then spray some pb on it. the heat will suck in the pb. let it sit for a good 2-3minutes then give it a go. Worked for us. We spent 2 hours trying to get the thing to budge before we thought of the heat, took us 5 mins to do with the heat.
04-15-2010 08:23 PM
1kooljeep Angle grinder with cut off wheel does the trick. But have some ventilation the rubber bushings smoke and smell real bad.
04-15-2010 08:11 PM
Snuffy115 I used a rotozip with a metal cutoff wheel to cut the bolts out. It worked faster than the sawzall.
I had to do that to all four main eye bolts. It sucked!
04-15-2010 07:53 PM
jpdocdave i've had many many of those spring bolts that simply don't come out, i've had to cut them inside the spring hanger with a hack saw. cut both sides that way and then the spring can at least come out. the bolt being stuck inside the spring and bushing makes it impossible to get heat on it, there's nothing to heat. a sawzall works, but i actually have more luck with a hack saw in the tight space. it actually doesn't take very long, and i'm a very impatient person.
04-15-2010 02:15 PM
chrisb0108 Just got back home and am about to try the heat. Go ahead and laugh but I'm using my wife's cooking torch...should work the same, I think!

Mr. C, can you elaborate? Have already disconnected the spring from the back shackle and have removed the u-bolts and plates from underneath, only thing left is the front bolt. We've tried moving it around while pounding, holding it up, down, etc...
04-15-2010 01:49 PM
MR.CLIFFORD Take the weight off the spring
04-15-2010 01:46 PM
minderbinder3 I had to cut mine with a sawsall. It sucked but was all I could get between the spring and bushing. I did not try heat though.
04-15-2010 12:37 PM
jdhallissey heat will be your friend. get the bolt to almost glowing red with a mapp gas torch then hit the end of it with a hammer. It will basically fall out.
04-15-2010 12:30 PM
chrisb0108
Can't remove spring bolt!!!!!!

Its the front bolt on the passenger side< rear leaf spring. Have tried hammer, impact wrenches, levers, PB of course.....any ideas would be greatly appreciated?

2.5, 94' YJ installing 4" Rough Country and am at a stand still for now.....

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:27 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC