|09-25-2010 09:03 AM|
|ted4ags98||To HYPERBUZZIN, you are correct, the 1/4-20 would have worked, but really concerned about stripping interior bolt, so didn't want to take the chance. And to HOSTILE, the guards are just a personal preference. I'm the original owner of '90 Sahara that has many well spent upgrade that I have personal tackled with great pride (4" lift, 33x11.5, aftermarket carb, winch, SRC front/rear bumpers, all the Hi-Lift items, body armor, interior liner, stereo, etc...........oh, also front light guards). If I get bored with the looks of the light guards, I simply take them off and give them to my other JEEP friends.|
|09-24-2010 07:52 PM|
|Hostile JEEP T.J||Yeah don't buy tail light guards!!!!!! There worthless and the lights aren't that expensive if you crack or break one on the trail! Sorry but I really think guards u put on any lights look stupid!! Sorry I'll spend my money on more important stuff on my jeep.|
|09-24-2010 06:24 PM|
|Atthehop||Rugged Ridge shold provide the correct mounting hardware. Everyone who has purchased them should pound their customer support and boycot them until they fix their problem.|
|09-24-2010 06:06 PM|
|HyperBuzzin||Why did you HAVE to go with 12-24? A 1/4-20 probably woulda worked, just have to (maybe) make the hole a little bigger.|
|09-24-2010 07:31 AM|
|ted4ags98||I just installed the Rugged Ridge tail light guards. I had to find a #12-24 machine screw (the 24 is the pitch pattern). This is a hell of a hard screw to find, actually had to go to specialty fastener distributor. Finally found the #12-24 at 1" in length (has a phillip screw driver head instead of a hex head), got some #12 washers (1/4" will also work). Everything worked perfectly. Remember, the bolts also ground the tail lights, so get a good connection.|
|04-28-2010 11:29 AM|
Of course - now I want to install flush lights anyway.
|04-28-2010 10:28 AM|
|sedty||Glad I found this post, I have a set of them on order.|
|04-27-2010 01:05 PM|
You'd be much better off with nuts/bolts and large washers.
with just self tapping screws (besides the possibility of stripping them out on installation) there's not much holding them on if ya do hit something with them.
Get them mounted securely, not just barely!!
|04-27-2010 09:00 AM|
|abw0004||I actually stripped the holes out using the screws that came with it, so I went to Ace Hardware and got slightly bigger screws. Be aware that the screws can cause a problem with the connection from the lights to the tub, making the car think the light is out.|
|04-27-2010 08:40 AM|
I was wanting to use the same type of self tapping screws that were in the jeep without rethreading the holes or using nuts and bolts.
Thanks for the replies.
|04-27-2010 08:25 AM|
There's nothing special about them, other than the right size to fit the holes. Stainless, as Wes suggested, would be the best to use.
|04-27-2010 04:44 AM|
I had the same problem with mine, as have many others.
I ended up using some stainless steel bolts.
|04-26-2010 10:25 PM|
Rugged Ridge Tail Light Guards
I bought a set of these tail light guards last week online and the screws that came with them are to small. The screws from the tail lights are too short. I have looked everywhere (Auto parts stores, Chrysler dealership, Home Depot, and hardware stores) for the 6 screws that hold the tail light and tail light guard to the body of the Jeep Wrangler to no avail.