Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > installed new motor, spewage/leakage

Join Wrangler Forum Today

Thread: installed new motor, spewage/leakage Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-17-2010 05:23 PM
ratuna Glad you found the problem and it's a very cheap fix!
05-17-2010 01:32 AM
itsawhr08 picked up a new p/s pump for 16 bucks at a local junk yard. after removing the old and cleaning it up a little more i found a large crack and hole in the pump near one of the bolt holes. thanks for all the info ratuna. appreciate the help.
05-16-2010 02:39 PM
itsawhr08 update: just put more fluid into reservoir and it leaked out the back of them pump immediately. assuming the pump is bad. going to see if a junk yard has a decent one.
05-16-2010 02:11 PM
itsawhr08 ok after looking again it seems to be coming from one of the hoses. and yes it is belt driven. a pic at this point wont do to much but i will take one soon. everything is pretty soaking wet from fluid.
05-16-2010 12:22 PM
ratuna The power steering pump? Get a new banjo bolt and/or a washer for it while you are at it and replace that as well. I'm pretty sure the PS Pump is belt driven so it should be on a bracket and not directly to the motor so it wouldn't be gasketed to the motor. This is why I say we need a pic to help you better.
And be sure to top off the PS fluid before you start it again if that is what is leaking so you don't ruin the pump by running it dry!
05-16-2010 12:10 PM
itsawhr08 well i cant tell exactly. it shot up onto the windshield. all over the fenders. i will try to take it off. i dont know if its from the hoses or what. i will run to an auto parts store and see if i can get a gasket. as for the pic part. the majority of the fluid seems to be from the pump.
05-16-2010 12:03 PM
ratuna Figure out exactly what it is that is leaking, maybe post a pic of the part here. Then try to see exactly where it is leaking from. If it is where this part mates to the block remove it and clean both contact surfaces. Put on a new gasket put it back together and try again.
05-16-2010 11:54 AM
installed new motor, spewage/leakage

recently purchased my first jeep, as a project, installed a new motor and started it finally this morning. after initial start up there was a spewing leak from what looked like the power steering pump, bolted to the block. i can not tell what the smell of the fluid is. some coolant was mixed in due to a loose cap, but the leak still continued to shoot around the whole engine bay. btw this is a 97 tj 2.5l 4 banger. i believe all the vac lines are hooked up correctly but i do not believe this would be an issue if the motor starts and runs good at idle. and it does not leak consistently, it happens at random, sometimes at initial start, or sometimes after its been running for 2-3 minutes.
please help would love to get this jeep running today!!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 11:50 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC