Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Body Lift Question

Join Wrangler Forum Today

Thread: Body Lift Question Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-05-2007 11:40 AM
jherrin215 That's about the jist of it. They come with stud extenders and bolts and that's it. Pretty simple setup really.
04-05-2007 08:34 AM
erickpl Aluminum block 1" thick.

2 holes.
04-04-2007 06:35 PM
Triple88a any one have a blueprint of a motor mount lift spacer?
04-04-2007 02:49 PM
erickpl NP. Glad to help.
04-04-2007 02:35 PM
jherrin215 Thanks for that link eric, that should really help me out!!
04-04-2007 08:11 AM
erickpl JKS spacer motor mount lift
04-04-2007 01:12 AM
RedRubiTJ Yes. The order you have is good just don't start the engine until both are completed as the fan will hit the shroud. Leave enough slack in the "hand tightend" side to allow for movement when doing the other side.
04-04-2007 12:44 AM
jherrin215 Thanks, that's what I was hoping. I was going to do the MML 1st then do the BL as soon as I got done. So the only things I should really have to do are, Do the MML, Then Just loosen the Body mounts on both side, remove one side, jack it up, put in the blocks, hand tighten 1st side, then jack up 2nd put in pucks and then tighten all the bolts right?? If it is like I think should be easy enough!!
04-03-2007 11:54 PM
Triple88a i believe although you are installing mml and bl you still have to disconnect the fan shroud unless you are doing the bl and the mml at the same second 4th by 4th lol
04-03-2007 11:02 PM
NalinMFG are there any write ups for a MML? i understand where they go and how they go there.... but i like pictures
04-03-2007 10:32 PM
binaryking yeah the fan shroud is really the only thing you HAVE to do when installing only a 1"BL. And with the MML, you can skip it.
04-03-2007 05:32 PM
1BLKJP Doing the motor mount lift you are going to be able to skip moving the fan shroud and more than likely the linkage. Just add in your MML and then you BL and see how the linkage feels. Everything else you won't need.
04-03-2007 03:33 PM
Body Lift Question

I am going to be installing a 1 inch performance Accessories Body lift this weekend as well as a JKS motor mount lift. I was wondering if anyone knew where there was a good write up about a similar installation that i could look at. The body lift has instructions and the MML has instructions but I know there will be some steps on the BL I don't have to do using the MML. I found this---> and it uses a LOT less steps than the instructions with the BL but doesn't use a MML. Is it as simple as what he says or do I need to go through all the steps that they show in the BL instruction booklet?? Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 11:45 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC