Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Valve cover leak

Join Wrangler Forum Today


Thread: Valve cover leak Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-11-2011 09:44 AM
Swanktify2
Quote:
Originally Posted by mike_b_ar
i finally got my rear main seal fixed so it's not leaking anymore. Unfortunately, i discovered the valve cover was leaking pretty bad. I had replaced the gasket several months ago with a foam gasket, and i thought it was fine. One thing that surprised me was how low the torque specs for the valve cover bolts is. According to haynes, it's just 55 in-lbs, which is about 4.5 ft. Lbs.

Does this sound right? Is it the same for a foam gasket? I'm thinking i'll torque them down a little bit more just to see--can't make things worse.

If that doesn't work, should i just go with the blue rtv gasket maker instead, or maybe a combination of both???

Thanks!
dont torque more than it says to.
08-11-2011 09:42 AM
Swanktify2 It doesn't matter. Especially not if you're using RTV. There's about ten bolts. The ones in the back are a pain in the ass. Do the middle two, (yes, the "bolt within a bolt" ones) then do the corners starting in the back, then fill the rest in. Tighten them until they show a little resistance and then stop. They're designed to snap after over-torquing. Then backing them out is a bitch.
08-11-2011 07:29 AM
onroad I checked Alldata which doesn't give the tightening sequence. In which case an official diagram might not exist. Just start with the bolts in the middle, and work your way out in sort of a spiral pattern, and you'll be fine. It's not nearly as critical as head bolts.

I'm not sure how many bolts are actually there but just follow this as kind of a general rule of thumb:


08-11-2011 01:10 AM
Firemangully Thanks for the info guys, still trying to find the correct order for tightening the bolts. Google here I come.....
08-10-2011 05:03 PM
Garyk I use black RTV, run a good bead on the cover, let it set up a little, then install, no leaks
08-10-2011 07:38 AM
Wirenuting The pattern is important in the respect of not warping the cover.
You do want to tighten in an X configuration pattern.
Snug them down, then tighten them down, then torque them down.
Repeat torque sequence until tight.
If you use the wrong gasket then it can come loose over time.
But normally properly torqued bolts work loose quickly when the threads on the bolt or head are worn down.
All threads have a slight taper to them.
If you find that the threads are worn & you can not make a proper repair, try a little of the proper thread lock compound.
Be aware that once you use thread lock, it's a pain to try and remove them later when a high temp locking compound is used.
08-10-2011 07:26 AM
Firemangully Does anybody have an update on this or the correct order for tightening down the bolts? I have heard work from the inside out and also an X pattern. I am assuming this means start in the middle and work out in a "criss cross" fashion. Any other info on this from anybody would be greatly appreciated. I have a minor oil leak which is gettting worse from my valve cover on the firewall side that I am trying to take care of.

When I inspected it this morning I found the bolts holding the valve cover down to be loose enough to unscrew with my thumb and forefinger.

Thanks!
08-29-2010 10:25 PM
FNjeep The torque is right, but there's a specific pattern you need to follow when tightening the bolts on the valve cover.

Also! Tightening the valve cover is a two step process. It's a double torque down process - you tighten once to a certain level, then you tighten down again.
08-29-2010 09:18 PM
mike_b_ar
Valve cover leak

I finally got my rear main seal fixed so it's not leaking anymore. Unfortunately, I discovered the valve cover was leaking pretty bad. I had replaced the gasket several months ago with a foam gasket, and I thought it was fine. One thing that surprised me was how low the torque specs for the valve cover bolts is. According to Haynes, it's just 55 in-lbs, which is about 4.5 ft. lbs.

Does this sound right? Is it the same for a foam gasket? I'm thinking I'll torque them down a little bit more just to see--can't make things worse.

If that doesn't work, should I just go with the Blue RTV gasket maker instead, or maybe a combination of both???

Thanks!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:28 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC