Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Only 4th Gear in AX15

Join Wrangler Forum Today

Thread: Only 4th Gear in AX15 Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-30-2010 10:48 AM
jeeping68 So it turns out the teeth on the input shaft were completely ground off. THis in turn chewed up the mating gear on the cluster gear shaft. Looks like I will be calling wrecking yards looking for a good used unit. One of my buddies suggested upgrading to a NV3550 while I was at it. What's the story on the 3550? Is it a better trans? What would it take to mate everything up to the 4.0 engine and the NP231 transfer case? Any thoughts would be appreciated.
08-26-2010 10:06 PM
Abomination93 if you need the actual gears, buy a used tranny, way too expensive to buy new gears. you could buy a new tranny for less than all the gears and idler shaft. if you need anything it will be bearings and sychros and those will come in the rebuild kit if you get a good one.
08-26-2010 03:41 PM
Ibuildembig Man I dunno about might be able to get um from Dodge still.
08-26-2010 03:34 PM
jeeping68 Makes sense to me. And I figured that a rebuild was looking more and more likely. Obviously a rebuild kit is not going to come with anything more than bearings, seals and synchros. Anybody have a good source for any new gears I might have to purchase?
08-26-2010 01:59 PM
Ibuildembig its because in 4th the ratio is 1:1...everything is aligned and its straight through from the input to the output. If it stuck there you need a tranny....or at least a rebuild
08-26-2010 01:50 PM
jeeping68 She lost gears 1-3, 5th and even reverse. My initial thought was the clutch, but if that was the case, why would 4th gear grab so firmly. I can start off in 4th gear from a dead stop without any slippage at all.
08-25-2010 04:33 PM
wasomma do you mean she has lost 1-3 and 5? Sounds like your clutch is slipping and needs servicing.
08-25-2010 01:54 PM
Only 4th Gear in AX15

My wife was cruising along on the freeway in 5th gear when the engine starting revving up and the Jeep started slowing down. She pulled over and couldn't get the Jeep to go anywhere. Upon further messing around, we discovered that she has no gears except 4th gear. In addition, you can switch the gears to any other gear except for 4th without the clutch. This includes reverse. Fourth gear works just fine. You can push the clutch in and as long as you feather the clutch and give it enough gas, you can get it moving. This is a 93 Wrangler with the AX15 transmission. Any ideas anyone?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 11:56 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC