Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > ?'s about intalling Bestop no drill header bar and safari top

Join Wrangler Forum Today


Thread: ?'s about intalling Bestop no drill header bar and safari top Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-09-2007 09:28 PM
Jackie I just ordered one from these Bestop Performance Parts. I wish I wouldn’t have hard time with the installation. Anyways, if I’d have, maybe I wouldn’t think too much because I not got some few points from this thread. I really love this site. Solutions are ready made. I just have to search, browse and have fun.
05-07-2007 06:58 PM
Jerry Bransford The windshield channel that screws onto the windshield frame mounts on the INSIDE rear-facing edge of the frame, not on the top of the windshield frame. The little cut-outs on the ends of the channel halves face downward to give room for the footman loop. So the channels will be vertical against the windshield frame, not laying flat on top of the windshield frame.
05-07-2007 06:54 PM
blownfanswitch Erick has the right idea...it looks like it'll never work, because it sits at a funny angle when you mock it up, but if you hold it in place and tighten it, it'll work like a charm...I've never had any leakage or problems with mine
05-07-2007 09:56 AM
erickpl No I did not. I missed that part of the post - it was early.

I know of several people who have the hard top and put on the no-drill header and they didn't remove anything either. If it is anything like my soft top's strip is, when you tighten the clamps on the no-drill it may seem a bit of an off angle. I held it down tight while tightening to ensure it sits on there properly.
05-07-2007 08:43 AM
Hank Did you have a factory hardtop?
05-07-2007 08:07 AM
erickpl I didn't remove ANYTHING to put on my no-drill header. You remove that rubber and you'll have a lot more rattling and likely water coming in that way when it rains.
05-06-2007 04:54 PM
foxinthemudd take a look at Windshield channel posted by fondo23, I think this is what your talking about.
05-06-2007 03:54 PM
Hank I'll try to get my hardtop off sometime today and give yall some more info and maybe some pics.
05-06-2007 01:35 PM
blownfanswitch I have the same top you have. I ended up having to pull a metal strip off the front of the winshield frame....it was screwed in. I'm not sure exactly what we're dealing with here, what I remember a/b mine is that when you bolt the header to the slots (the soft top slots) it's a tight fit. you just kind of have to hold it tight and then tighten it down. We had trouble getting it to fit, but we just kinda put it on there the way it looked the most secure and tightened it down. If the rubber thing is what i think it is, the header may have a channel on the underside to fit it....if not, there may be another header....i think when i ordered mine she made me specify that i had a factory soft top
05-06-2007 01:19 PM
Hank
?'s about intalling Bestop no drill header bar and safari top

I'm planning on putting on my new safari top this weekend on my 03 TJ. I was wondering if I need to remove the rubber piece that goes in-between my windsheild frame and my hardtop? It appears that this is held into place with some double sided tape. I have the no drill header bar from Bestop if it helps any.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:16 AM.



Jeep, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC