Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Axle shaft seal questions

Join Wrangler Forum Today


Thread: Axle shaft seal questions Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-18-2010 06:57 PM
Jerry Bransford D-30 Axle Shaft Seal Replacement - 1

Pulling the axle shafts is easy. Pull the brakes off, remove the bolts that hold the unit-bearing hubs to the knuckles and then pull the shafts out.
10-18-2010 06:25 PM
p1zzaman nobody?
10-18-2010 11:16 AM
p1zzaman Any other input on this?
10-17-2010 06:19 PM
p1zzaman Thanks for that info. Colorado has lots of mud and dirt roads, so I think its a good investment for me. How hard is it to pull the shafts and replace the seals? I have been reading write ups, and it doesn't seem all that hard, but I'm very nervous about messing with the diff's, cause I'm new to most of this.
10-17-2010 06:08 PM
adkjoe I can comment on #2. I installed the alloy usa seals because we have a lot of mud and crap up here and the factory seals do nothing more than keep out large rocks and sticks, there just plastic discs. I pulled my driverside shaft one day and the tube was filled with mud and crap. I cleaned out the tubes on both sides and put in a set of the tube seals and went about normal business for a couple months. I recently pulled the same shaft to change a u-joint and the inside of the tube was spotless. They definitely work, and are good if you live in a muddy, wet place like me. If you live in the desert you probably could spend the money elsewhere but they were definitely worth it for me, I found them on ebay for $50 instead of the $70 Quadratec wanted look around you can get them pretty cheap.
10-17-2010 05:47 PM
p1zzaman
Axle shaft seal questions

My driver side front axle shaft is leaking, and I am getting ready to replace the seals on both sides.

My first question is what's the best seal to replace it with, factory or is there a more heavy duty one I could buy. I have been researching a bit, and found this one on quadratec Original Replacement Parts 8121781 - Inner Axle Oil Seal for 72-06 Jeep® CJ, Wrangler YJ & Cherokee XJ with Dana 30 Front Axle - Quadratec is that what I need, or is there better? It fits both passenger and driver side, and I'm going to replace both at the same time since its only 5 bucks and you have to take the shaft out anyways...

My next question is about outer axle shaft seals. Is it worth the 75 or so dollars to add these when I replace the inner seals? Just not sure if they actually work or if the factory guard on there is good enough. These are what I have found and am considering purchasing, but would like to know any first hand experience with them. Original Replacement Parts 11102 - Alloy USA Axle Tube Seals for 84-06 Jeep® Vehicles with 27 Spline Dana 30 Front Axles - Quadratec

Thanks for any info


Also here is a pic of what it looks like

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:31 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC