Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ General Discussion Forum > springs over axle?

Join Wrangler Forum Today


Thread: springs over axle? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-19-2006 01:05 PM
KeepItCrunk SOA (Springs Over Axles) 101.
What you want to do is a spring over lift. Right now it might look cheaper, a little bit of welding and some perches, shocks, be all set right? wrong.
First you will need to find the degree in which you want your perches to be placed, make sure it keeps a good pinion angle throughout suspention travel. Thats probaily the most minor of issues.
Your now also have to adress your steering. You can get away with a dropped pitman arm (75-125 bucks). That will work for mild stuff, but it will have serious bump steer. If your keeping the stock steering setup you will need to have someone build you a 2 inch drop drag link. That will cure all your steering issues, however it will leave the steering in a venerable spot... under your springs. When doing a spring over it is more then wise to invest in a crossover steering setup, which relocated the tie rod to the top of the steering knuckles instead of under them, and under the springs.
With that said driveline issues will need to be adressed without a doubt. Your transfer case is fitted with what they call a slip-yolk. It lets the driveshaft slip in and out of the transfer case when your suspension compresses from offroad obstacles or from bumps on the street. If left stock, your driveshaft will mroe then likely fall right out of the tranfer case. The angler of your driveshaft will be horrible as well, and if it were to actually drive without the shaft falling out you would eat up universal joints faster then a fat kid eats cake (no offense to the big ones). You would need to invest in a Slip-Yolk Eliminator and a rear CV style driveshaft. The SYE eliminates the the slip-yolk, obviosuly. It gives you a few more inches of driveshaft to help the angle out. The CV shaft will let thedriveshaft slip on itself and lengthen adn shorted as needed, not to mention they are much stronger and can be used on much steeper angles. A SYE kit and driveshaft will most likely run you around $250 for the SYE kit and around $100+ for the driveshaft, depending on how good of a looker and deal finder you are.
With those two things said your already spending as much as you would have on a normal 4 inch lift, and those are only the things you will need.
Another thing that you will surely feel, is axle wrap. You get that because you have all this extra torque on your springs because of the springs being on top. When you hit the gas, the rear axle, if your looking at the passanger side fo your jeep, the rear axle wants to rotate clockwise. When you take off, or are trying to crawl, it will load up like that until it cannot hold anymore and then it will unload and cause a hop. On pavement if your hit it raelly good, or the same on rocks, lets jsut hoep you have a good dentist because it will knock your fillings out. There are many ways to combat this. You can make a traction bar, which will keep it front wraping, but willlimit travel a bit, and give your rig something else to hang up on. Or build your own good spring pack. If your using stock springs for your SOA (youll get maybe 5 inches and AWESOME flex and no noticable difference in ride), take another set of factory springs, cut the eyes off both ends, and put it on TOP of your spring packs top leaf. It will almost fully cure the axle wrap problem, and trust me on that one. Or, you can buy Rubicon Express' spring voer spring. There great, but there stiff as hell... and you need to pay for them, and then you might as well have bought a 4 inch skyjacker or w/e you wanted, unless your going for built.
Another minor issue you will find when you elast expect it, is your shackles flipping. When there in the front, like they are on yj's, they let the axle spring forwards. If you have a SOA and you romp on the skinny pedal in reverse, your shackles will flip up and it iwll not only drop the front of your jeep about 3 inches, but it will stress your springs like crazy, if not break them. Get a pry bar adn flip them back ASAP if that happens. But again, to combat that, you can buy a shackle reversal. those can range anywhere from 150 to 300 bucks depending on your skills, access to a welder, etc etc.
So now you have to think about something, are you building a semi-built jeep, or building a built jeep. If you want to run 31's locked max, or 33's open max, keep the stock axles. As we all know the rear dana 35 is somewhat of a junker axle and have been scince the early days. I know everyones freidns brothers cousin ran 35's with a detriot on a d35 for 3 years and it never broke, and i know that everyones siters boyfriends uncle ran one with a 4 popper yj and 30's open and broke a shaft. The rear truth is, anything over a 33, the D35 is useless. So you can either swap in an axle with this spring over, like the ford 8.8, or use the axle and face the facts of killing it sometime soon.
The front axle, the dana 30 is a great little axle for what it is. Many people run them on somewhat built rigs without a problem. The key is to have the shafts from a 95+ jeep, becuase they use the stronger 297X u-joints (same as a dana 44) the 87-94 yj's in particular used 260X's, which are not bad... jsut much less strong the the 297's, easy swap if you find the shafts. The axle itself will hold up to a 35 without much trouble actually. The only stupid thing about them as that vacuum disconnect thing. If they work, consider yourself lucky becuase the first time it gets cold nad you need 4wd in snow, they will crap out. as mine did... 2 times.... before i smartened up and bought a posi-lock. But if your going the route of welding on perches anyways. get a dana 30 out of a cherokee, its a high-pinion like the yj's, but without the disconnect, and chances are in your favor of a 94+ having the better u-joints. Just grind off the old perches and weld on your new ones. your old steering, driveshaft, everything bolts right up, same exact axle jsut no disco.

So with alll that said and done, a proper SOA will cost you 3 times more then jsut a normal 4 inch skyjacker/fabtech/rancho/etc etc. its true, you can do a SOA for like 100 bucks, but if you plan to use it at all... do it right... and save all ur wheelin buddys the trouble of puttin ur rig back together and towin it home.
Go with jsut a normal 4 inch/3.5 or w/e lift if you jsut want a good jeep that works, with say 33's and good capabilities.
Go SOA and do axles if you really wanna wheel it, build it, spend the time and msot important money on it.
I been in the yj game for a while, and let me tell you, the only way is the right way. Not sayin the right way will never break, but it will last ALOT longer then the wrong way/easy way/cheap way.
first jeep for me was a a yj on 33's. She was locked in the back, hp d30, bumpers, 3.5 inch fabtech, coppped fenders, no gear, and i held up with the pack of everyone. Freak accident an bout 10k incl. initial cost was out the pooper. But now being around, watching friends, building rigs with friends... oh man did i learn lots...
03-17-2006 05:18 PM
bluvikng The thing to remember with a SOA is that you will have to build a link from the rear axle to the skid plate to prevent axle rap.
03-08-2006 08:49 PM
Felsengleiskette please let us know how it went...and give a detail of how it went. I want to do a spring over as well...I got a 4" skyjacker right now took me 10 hrs to do. want the spring over though...better articulation (less the springs gotta do sittin up on top like that... ) And its alot taller that way. ( down the road I want different engine/tran. in it and 36" tires) between the lift and a spring over that should lift it 8 inches or so...plus tire height
03-01-2006 08:01 PM
daddyjeep I was wondering where that was dumbass
just called you that because you did.
03-01-2006 05:10 PM
1BLKJP
Quote:
Originally Posted by 1BLKJP
Here's some info for ya on another thread about SOA setups for your rig. It has some of the things you are going to have to consider when doing it beyond just welding on new perches.
Yeah, so i'm a dumbass and didn't even put the link to the thread for ya. Here it is.

http://www.wranglerforum.com/f290/suspension-or-soa-lift-1168.html
02-28-2006 08:04 PM
18derrick quadratec has a spring over conversion builder kit p/n 16300 305
its 309.99 but aside from the shocks they say its everything you need there number is 1 800 745 5337 and they strongly recommend a cv type driveshaft.
02-28-2006 05:32 PM
1BLKJP Here's some info for ya on another thread about SOA setups for your rig. It has some of the things you are going to have to consider when doing it beyond just welding on new perches.
02-28-2006 05:24 PM
yj4me Still seems like a big bang for the buck since, I can do labor and welding myself,but I will look around for other option first. Any way I go Ill post pic.s and will no doubt be askin advice
02-28-2006 09:20 AM
whiteyj You are going to need new spring perches as well plus then have those welded to the axle tubes. So either a buddy that welds or pay a shop to do it for you. Shocks, etc. It all adds up pretty fast!
02-27-2006 08:33 PM
yj4me plenty of time short on money, just dont look that hard or expensive. am I missing something? angled shims for axle housing, u-bolts, pitman arm, shocks, plus other smaller mods such as brake lines etc? other than shocks thats only about $100.00 worth of stuff. keep in mind Jeeps are new to me
02-27-2006 08:28 PM
gutterboy2ca good if done right, but lot more work then say a 4 inch Rubicon Express lift,can do one of those in bout 8 hours with a set of torches Handy...
02-27-2006 08:23 PM
yj4me
springs over axle?

does anyone have info on putting springs over axles on a yj?
good or bad?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:42 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC