|03-20-2014 03:49 PM|
|Ibuildembig||A couple of them I did lol, I have several now|
|03-20-2014 03:37 PM|
|Bigwheelers1||Awesome I think i''l try that right now I'm guessing you got your angle finder at harbor freight ?! lol|
|03-20-2014 02:49 PM|
|Ibuildembig||It's worth a shot. Pinion might be too low|
|03-20-2014 01:26 PM|
|Bigwheelers1||great work big! I get the impression we are on the same page as far as our work I've got one question, I did my SOA last weekend, And I have a violent vibration that im certain is being caused from the rear driveline angle, I have the pinion kicked up a bit but i think the problem is up at the top..should i drop the skid down an inch or so?|
|02-08-2014 09:38 AM|
|02-07-2014 09:35 PM|
|Lt. Ray T.||Well, I done gone and dunn it!. Did my SOA today and look back and wonder, why did I ever buy a RC 4" lift in the first place. Drives better, rides better, I will be needing to do my anti wrap bar soon, but will fab that up myself with some guidance from this place. I like the wishbone you used in here, but think I will go with more of a ladder style. Anyway, thanks for this writeup, it helped a bunch!...|
|02-04-2014 10:22 PM|
|jack3d_up||Just read this whole thread and it seems like these questions are repetitive! Looks good man, bookmarked this thread for future reference!|
|01-21-2014 01:57 PM|
|Ibuildembig||You can use an extreme drop pitman arm ford a Ford superduty (I think they are the same spline) and if thats not enough your gonna have to swap out your knuckle for one that is flat enough to put an arm on.|
|01-20-2014 09:19 PM|
Here's a pic just because...
|01-20-2014 08:23 PM|
Help me, Obi Wan!
I saw this build thread when debating SOA vs SUA for my build and you convinced me to go SOA. I bought everything in your parts list to prepare for the build. I eventually located full widths to swap in (J10 44 and 20). I just put em in this weekend.
For the most part it all went well, it looks great! I just have one problem that I was hoping to pick your brain on...
I can't connect the steering. The drag link hits the passenger spring on right turns. Unfortunately my 44 isn't the flat top variety. What are some options for crossover or high steer?
Sorry if this was covered, i read all 21 pages once. Didn't want to do it again.
|12-10-2013 09:16 AM|
|Ibuildembig||I've only done that to one rig in my life and it had 20 inches of lift. 99 percent of the time on a jeep it will never be needed.|
|12-09-2013 08:49 PM|
|12-09-2013 08:29 PM|
|Ibuildembig||You mean roll the diff?|
|12-08-2013 10:10 PM|
|Razzer||I hate auto correct .... Cut and turn. Very sorry I didn't proof read my post. Lol|
|12-07-2013 11:18 PM|
|12-07-2013 01:46 PM|
|Razzer||Hey, Big! In this whole 21 pages I didn't see anything about custard turn on the front. Not that this set up needs it, but do you have thoughts on the process? I've had Ty's and hate steering issues. Trying to get it right the first time. Thx|
|08-21-2013 01:37 AM|
|08-08-2013 10:58 AM|
|devilrmk||You can always pull one of the shorter springs out of the pack to soften them and drop it a bit. I had to do that with mine.|
|08-07-2013 12:33 AM|
|08-02-2013 03:08 PM|
|ziloh22||man im really debating doin this.. i already have 2 axles with SOA setup..|
|08-02-2013 08:09 AM|
You can run 35's with a soa+2 with no fender issues, 37's with a little fender work.
Soa+2 is. Borderline too tall.
|08-02-2013 12:08 AM|
|08-01-2013 09:22 AM|
Mine was 5.5" with a D30 and Ford 8.8 and another 1.5" using Rubicon Express RE1445 springs, for a total of 7" of lift.
|08-01-2013 09:12 AM|
|jeeperthing||Doing a SOA doesn't it give you like 4" lift?|
|06-26-2013 07:32 PM|
|06-25-2013 05:59 PM|
|Ibuildembig||I mocked rear pinion angle, front is stock. Rear is approx 2 degrees below driveshaft centerline.|
|06-25-2013 02:50 PM|
|amerdt4||Did you mock the pinion angle at full droop or sitting on all 4 wheels? Did you set straight on or a few degrees under to compensate for torque wrap under load ?|
|06-25-2013 07:13 AM|
|06-25-2013 04:47 AM|
|amerdt4||If I cut a piece out , what would I have to reweld? I was thinking just the lip of the skid plate|
|06-24-2013 08:58 AM|
|This thread has more than 30 replies. Click here to review the whole thread.|