|02-05-2013 03:51 PM|
|dave twombly||Also if you have a problem pumping gas and the pump shuts off too quick and you squeeze the handle three or more times to fill the tank rapidly it will also trigger the engine light. I wait a couple seconds and add gas slowly and after the second shut off I hang it up., No problems since.|
|02-05-2013 11:12 AM|
|sgwrangler||I had the issue where my check engine light would come on under heavy loads. It ended up being the #4 spark plug. The gap was incorrect so I was getting a misfire on cylinder #4.|
|02-11-2011 08:50 PM|
|Bryangb7||I have found on really cold days my o2 sensor throws a CEL but when the days get warmer it automatically clears out.|
|02-11-2011 08:13 PM|
|wrangler65||hello new to this website i to have same problem engine light but now comes for awhile then oneday light shuts off so next time lights up try the code see what it reads thanks sharing|
|02-10-2011 10:02 PM|
Very helpful didn't know this was possible
Also the gas cap is a very good chance . I failed emissions with a 5 month old gas cap . Luckily I always bring a new one , changed it and passed . After replacing gas cap it will take about 20 miles for check engine to go off (if it was the problem)
|02-10-2011 09:56 PM|
|Jerry Bransford||You don't need his OBD II scanner to read your codes, you can read your own as described above. Done correctly, any diagnostic codes will display in your odometer. Read post #4 above carefully again, it tells you how to do it correctly.|
|02-10-2011 05:10 PM|
|TJ922||That's what I thought. I have a buddy with an OBDII scanner, and book, I'll borrow it from him. The good news is, the Jeep is running fine, and fuel consumption is about normal for a Jeep, (15-16 MPG All around).|
|02-07-2011 10:27 AM|
|Jerry Bransford||05-02 isn't a valid code. A valid diagnostic code for your 2001 would have been four numbers following a 'P' like P1234.|
|02-07-2011 09:51 AM|
|TJ922||Thanks everybody. My code read out as an 05-02? I pulled the negative battery terminal for a couple of minutes, and re-attached. The Check Engine light went out.|
|02-05-2011 10:57 AM|
Yep so long as you don't have a '98-'00 TJ, the years this ability was missing, you can check your own codes and there's no need to have your diagnostic codes read by an auto parts store. No need to push the odometer reset button in, simply turn the key on-off-on (but not to Start) three times within five seconds and then leave it in the on position. Wait, give it time as the codes don't appear instantly, it takes several seconds for the diagnostic routine to run.
Check your gas cap too. If it is loose or if it was off when you started your engine, that will cause a Check Engine light. Sometimes a Check Engine light is set by a momentary glitch too. You can reset the light by disconnecting the battery's negative lead for 2-3 minutes. If the CEL comes back on, then it's time to look into the code reported by the diagnostics and figure out its root cause.
|02-04-2011 06:14 PM|
|vballspen||Advance auto parts lets you use there code readers for free.|
|02-04-2011 05:45 PM|
Turn your key to the on position (not start), off, on, off, on wait a few seconds and the code will appear in the odometer window. After all codes are shown it will read "done"
Then go here to check the code meaning.
Most Complete List For Jeep Check Engine Light Codes
|02-04-2011 04:56 PM|
Check Engine Light came on this morning.
My check engine light came on this morning on my way to work. I didn't hear anything, or experience any power drop off. I will check my gas gage on the commute home tonight. Me thinks it is an o2 sensor.
I read in here somewhere that you can check the codes by pushing the trip reset, and rocking the key 3 times, (is this true)?
I have a 2001TJ 4.0 with auto.