Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Rear Bumper Fix

Join Wrangler Forum Today


Thread: Rear Bumper Fix Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-07-2011 04:04 PM
coop0589
Quote:
Originally Posted by NHrubicon View Post
Look for 'scraps' and scratches on whatever he has for skids underneath, transfercase support, gas tank...that's a clue to 'offroading'.
Taking the bumper itself off is just presoaking the nuts in PB Blaster for a couple days, get a wrench on them and tape with a hammer a good one if you can get to it to 'break' the nut loose, then back them off, tap the bolts out (chances are good if one side is bent there is stress on the closest bolts) and then remove everything and bolt on your new offroading heavy duty steel replacement bumper you wanted so bad! LOL...at the worst it takes some elbow grease or an air wrench but we've taken off a few of them to replace with custom builds and never had to cut a nut off...
Thank you for the insight.
02-07-2011 04:00 PM
NHrubicon Look for 'scraps' and scratches on whatever he has for skids underneath, transfercase support, gas tank...that's a clue to 'offroading'.
Taking the bumper itself off is just presoaking the nuts in PB Blaster for a couple days, get a wrench on them and tape with a hammer a good one if you can get to it to 'break' the nut loose, then back them off, tap the bolts out (chances are good if one side is bent there is stress on the closest bolts) and then remove everything and bolt on your new offroading heavy duty steel replacement bumper you wanted so bad! LOL...at the worst it takes some elbow grease or an air wrench but we've taken off a few of them to replace with custom builds and never had to cut a nut off...
02-07-2011 03:52 PM
coop0589 The owner told me that he never took it off road, chances are that he may be telling the truth because when I did take a look underneath, it was rather clean with no mud stains. As for the bumper, he said that he backed into something but can't remember what. I'll be sure to take a closer look at that when I go back if I decide to make an offer. I would have spent more time inspecting the Jeep but it was in the teens and I was freezing my arse off.
02-07-2011 02:43 PM
InfernoGirl Look it over well.... TJ bumpers are pretty tough, except for the jugs on the ends... Chances are good he backed into a tree or rock on a trail..... Check for trail damage underneath...
02-07-2011 02:16 PM
KawiMonsterSahara you need to look at any frame damage right there where the bumper mounts to the frame...

(from experience... my jeep has been totalled TWICE)
02-07-2011 02:15 PM
coop0589
Rear Bumper Fix

I'm currently looking at a 2002 TJ that I may purchase. On this TJ, the owner told me that he backed into something so the bumper is somewhat pushed in on one side. If I did buy this jeep I would probably replace it with an aftermarket bumper, but being pushed in on one side would it be hard to remove and simply install the new bumper? I don't know if there's any damage underneath, something I will look at more, but by the looks of it I don't see any damage. The rear bumper is factory.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:52 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC