|09-03-2014 07:47 PM|
|raif281||awesome write up man!|
|08-28-2014 04:56 PM|
|08-27-2014 11:41 PM|
|08-27-2014 12:31 PM|
Yes the alternator only produces enough current in order to maintain proper float voltage (13.8v nominal). If all you do is change the alternator and you do not increase the system load you'll have the same current flowing from the 160a as did the 117a alternator.
You should not have any problems unless you add load that causes the alternator to produce more than 117 amps. Typically this will only happen if you operate a winch, boost another vehicle or add some other substantial load. The worst that can happen is you will blow the fusible link.
I ran mine for a couple months until I found a wiring harness from a vehicle that came with a 160amp alternator. If you plan on using a winch you should most definitely upgrade the wiring including the negative wires. Refer to my previous post where I circled in red the wires that need to be changed.
|08-27-2014 12:27 PM|
|jeepwayoflife||You are fine with stock wiring until you require the alternator to push high amperage, yes.|
|08-27-2014 12:13 PM|
Am I correct in my interpretation in the way I read your comments....? The 160AMP alternator is a passive device that will NOT produce more amperage than is being pulled. So I don't have to rewire until I actually add new load (winch, AC, lights, etc.).
Also asking because what I ultimately want is a dual battery system and I think some of the rewiring comes with the battery kits. I'd like to swap the alternator for 160 right now because my 117 is shot, but wait on the rewire. Thoughts?
|08-27-2014 11:15 AM|
|tjstillwell||Nooooo touchie! Thank you!!|
|08-27-2014 05:57 AM|
If you load and run your system over 117 amp your wiring is certainly going to heat up more than it was designed for. There is probably enough safety margin designed into the wiring that it should not be a fire hazard but it would be advisable to upgrade your wiring so that you don't exceed or run over the thermal limits of the insulation.
I added 700w (60a) of extra lighting load so I opted to upgrade my wiring because my base load increased substantially.
The fusible link will be the weak point in your system if not upgraded. It will get quite warm under max alternator load. If you don't believe me try winching a heavy load for 10-15 seconds where the alternator is maxed out then touch the fusible link. If you upgrade the fusible link you must also upgrade your wiring to match.
|08-26-2014 09:31 PM|
alternator upgrade plus wire guage upgrade?
I'm about to upgrade a 2001 TJ, 117AMP with a 2001 Dodge Durango 160AMP. I'm a rookie; this is my first upgrade, but want to learn. Looking at the spec pictures for each alternator, they appear the same in terms of mounting posts and plug.
Will I have to upgrade the wire gauge?
Are there any other things I should be considering?
|03-27-2014 11:20 AM|
Guys no disrespect to anyone here as I am only trying to help but there is a serious flaw in the OPs setup, if you connect the alternator directly to the battery like the OP posted you are exposing yourself to a serious fire hazard.
The OP has removed the protection to the alternator by connecting it directly to the battery. The stock rating for a TJ battery is 600 cranking amps, so if the alternator shorts your going to have at least 600 amps going to ground and your battery and/or alternator and/or wiring could potentially catch fire. Its even worst if you have a larger battery or dual batteries where the fault current can be as high as 1000-1500 amps. Very bad idea without a fusible link.
The second issue I will bring up from the discussion I've read is everyone seems to think the fusible link protects the PDC and/or battery from the output current of the alternator - IT DOESN'T - The fusible link is there to remove the alternator from the circuit in case its shorts to ground. It has nothing to do with protecting the PDC or melting if the alternator output increases beyond 160a. For that matter its impossible for the alternator to produce more current than its rated max current. The fusible link needs to be properly sized so that it doesn't heat up beyond its rated temperature rise spec during full load current (160a). Running a 10awg fusible link for a 160a alternator will get really warm to the touch after hard winching for a couple minutes. Will it probably work, sure, is it 100% safe no, because running a conductor above its rated allowable temperature rise will cause the insulation to fail over time as it will get brittle and crack.
So for this 160a swap to do it right you need to upgrade the following,
NOTE: all the following wiring must be upgraded, not only the fusible link and alternator wire.
1)Fusible link needs to be increased from 10AWG to 8AWG.
2)All wiring including the alternator wire, wire between the battery positive post and the PDC, AND both negative wires need to be increased from 6AWG to 4AWG.
Starter wire can stay the same as its unaffected.
Just follow the diagram below, the engineers know what they are doing, and you'll be safely protected.
|10-09-2013 11:08 PM|
|10-09-2013 06:35 PM|
|08-11-2013 02:38 PM|
Well I was skeptical, but I replaced my stock (remanufactured) 117a alternator with the 160a durango alternator and my voltage drop problem is gone. Before the upgrade I was experiencing some pretty good voltage drop at idle with the ac and all 4 stock lights (stock wattage bulbs with upgraded harnesses) on. I'm talking a drop from 14.4 to 12.5. Lights would dim, dash would dim, blower would slow...
After the install the voltage meter doesn't even twitch with the 4 lights on and the ac blowing. I'll need to wait until dark to see if the lights still dim.
Overall: I'm very happy with this. Advanced has a 15% off coupon code if you buy online and you can pick-up in store that same day, btw.
|07-31-2013 11:10 AM|
|Greeneggsam||Cool! thanks. I know the optimal is 175, get that in there this weekend. thanks.|
|07-31-2013 11:09 AM|
IMO You won't have any problem.
|07-31-2013 11:04 AM|
Did this last night, put a digi meter inline of 4ga, but only have 200a fuse that came with it (ordered before I found this post), think I will be ok till I get a 175a fuse? Ordered one just now online, actually a handful.
Trimmed the Durango 160 alternator bracket some, was hitting the rail a little, I run this thing hard so didn't wanna chance some rubbage while krawlin at The Gap over curbs.
As said, and know this post has spider webs, but on newer TJ's the belt/pulley is same. Ran the 4ga to the oem fuse box and just cut the green wire/link and terminated it, then put the new 4ga coming from the digital fuse link directly to one of the two post on the top of the oem fuse panel. Had to trim the incoming area of the box just a little to allow the 4ga access to the post and stay off the highline fenders. Very easy!! 20 min tops on all, and that was mounting the new digital fuse link. Like having battery readout, if needed. May need to put a switch, not sure what this lil LED will do to the drain, showing output 24/7. Hmmm.
Anyway, wanted to run it with the 200a in there till my 175 arrives, any downside? No winching or load will be applied.
|04-17-2013 10:19 PM|
At idle, warmed up, in gear: 14.01 at both.
|04-16-2013 12:35 AM|
|Jerry Bransford||Relays are simple on-off switches that are normally very good at passing all the voltage given them. I doubt the relay (if properly wired) is the cause of the problem.|
|04-16-2013 12:31 AM|
|04-16-2013 12:19 AM|
|Jerry Bransford||13.8v is higher than it takes to run headlights at their full rated brightness, I'd be measuring right at the headlight sockets when the headlights are plugged in and powered up to see what voltage the headlights themselves are getting. I know you have an aux power harness for them but...|
|04-16-2013 12:15 AM|
Oh and at a cold start idle when the RPMs are up around 1000, I get about 14.75-15.10 volts at the battery and lights. They're also at full brightness.
|04-16-2013 12:10 AM|
|04-15-2013 11:54 PM|
|04-15-2013 11:51 PM|
|Jerry Bransford||Have you tried cleaning the battery connections and reseating (unplugging/reconnecting) both headlight connectors? As well as cleaning/tightening ground connections at the headlights, engine ground, and battery ground?|
|04-15-2013 11:46 PM|
|04-15-2013 11:42 PM|
Alternators don't put out any more amperage than is being requested by the PCM via the voltage regulator that is internal to the PCM itself. So if the battery is dead, the PCM will instruct the alternator to kick up the amps until the battery starts getting too warm at which time the alternator's output amperage will be decreased as directed by the PCM. A battery temperature sensor button mounted under the battery tells the PCM the battery's temp.
Unless the battery is severely discharged, the alternator will never put out even close its maximum amperage rating. In my 17 years of wheeling my TJs & doing regular winching, I never noticed my single battery & OE 117 amp alternator not being up to the task. Which includes having used the winch to drag my TJ off the trail so others could pass me several times on battery power alone when the engine couldn't be started. Even then it started after fixing the engine issues without needing a jump start.
|04-15-2013 10:56 PM|
|OhSixTJ||Also, is it worth the upgrade to go from 117a to 160a?|
|04-14-2013 11:22 PM|
|OhSixTJ||So regardless, whether you have a 117a or 160a, at idle you'll only get what the computer wants? Or do you get more at idle with this upgrade? Everyone says its a good upgrade but no one posts idle voltage/amps (like do extra lights stay bright at idle now or do they still dim) with the bigger alternators.|
|03-25-2013 11:45 AM|
|matt1513||What year Durango alternator works with a 97 Wrangler?|
|02-20-2013 03:20 AM|
The smaller green wire IS the fusible link safety device. You should see a green wire one size smaller than the red wire it is crimped to. Automotive manufacturers use that style because two crimp connections are cheaper than a fuse and fuseholder. But you must match the size of the fusible link to the maximum capacity of the alternator, if you used the 8-guage fusible link provided for your stock 117A alternator on the 160A alternator, it would blow the first time you exceeded 117A output.
You can use either a 175A fuse or a 175A circuit breaker to replace the fusible link, but the fuse is much cheaper.
Fusible links will never blow unless a short developes or there is a flaw in voltage regulation. Even then they will blow slowly after several minutes - they are only intended to keep the alternator (a relatively expensive part) from smoking due to a shorted battery cell.
|This thread has more than 30 replies. Click here to review the whole thread.|