Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > VDP Sound Bar with Dome Light Wiring

Join Wrangler Forum Today


Thread: VDP Sound Bar with Dome Light Wiring Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-28-2011 09:39 AM
jp2611
Quote:
Originally Posted by stimpy View Post
I got that same soundbar from Quadratec last fall. I hate the thing. It arrived with a broken dome light, and a speaker already breaking. The speakers sound like crap. The thing is such a cheap POS. I will wind up getting a few sound boxes and a decent set of speakers.
I have one as well plus some other speakers-and with the new headunit and the bar mounted over head like it just fine. Not crazy about the little lights though-thought they would work like dome lights and don't.
02-28-2011 09:34 AM
stimpy I got that same soundbar from Quadratec last fall. I hate the thing. It arrived with a broken dome light, and a speaker already breaking. The speakers sound like crap. The thing is such a cheap POS. I will wind up getting a few sound boxes and a decent set of speakers.
02-28-2011 02:01 AM
duaneduanet I called them when I had a question and got a person on the phone easily.
02-26-2011 10:36 PM
caperry88 I tried to contact VDP about the faulty light but no replies, I am wondering if this company is really legit?
02-21-2011 02:26 PM
duaneduanet I have the same thing installed in my jeep. I love them. I wired mine into the power from the old sound bar. I had to go with the pods cause I installed the Tuffy overhead console.
02-20-2011 06:20 PM
caperry88 So it was a combo of both solutions.

I grounded to the door check strap post and got the passenger side to work, but the driver's side wouldn't. So I proceeded to take the light assembly apart. Thankfully VDP design is such that I can totally remove all lighting components very easily. there were some loose wires, and I made sure that all the wires had continuity with the ohmmeter. Once everything was working, I put it all back together and spliced into the off road lights power and the dome lights are working great. Only thing is sometime I have to "bump"it to get the drivers side to work.
02-20-2011 04:06 PM
caperry88 I used an Ohm meter to see what resistance was directly from the end of the power to the end of the ground, it was around 8 ohms, so I am assuming there is not an issue in the wiring. I also noticed I only got a resistance reading when the left light was tilted one way or the other.

I will have to try grounding it to the door check strap post.

the wiring is this thing is typical to old bikes I fix up... nothing is as it should be!
02-20-2011 02:36 PM
Wrangler Haven I suspect it's your ground. The roll bar is a terrible place to ground because there is a rubber sealant underneath the mounts. Run your ground wire down the bar to the door check strap post or a seat mount bolt.
Also, if you want to tie the dome lights into the dash switch, there is a plug for each courtesy light near the door check strap posts. Some Wranglers only came from the factory with a driver's side courtesy light but the plug for the passenger side lamp is there too. It has both power and ground and is controlled directly from the door pins and dash switch.
02-20-2011 02:14 PM
amoujaffar Make sure your ground is clean and on bare metal and the positive can go just about anywhere depending on how you want it to operate.

If it still doesn't work I would check the light bulb and make sure its not blown.
02-20-2011 02:04 PM
caperry88
VDP Sound Bar with Dome Light Wiring

Bought and installed a VDP 6 speaker sound bar with dome lights. I was able to figure out the wiring for the speakers which are working great. The ground and power for the dome light, however, I am unable to figure out.

I tried to just attach the ground to the frame and wire power with fuse direct to the battery but nothing comes on.

Anyone know which wires I need to tie into? I was thinking of wiring into interior lights but when I turn them up all the way they do not come on so I believe the interior lights are inoperable. They dash lights only work if the headlights are turned on.


Thanks for the help,

Perry

1995 Jeep Wrangler 4

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:54 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC