Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Builders Corner > Ken's 1989 YJ Project

Join Wrangler Forum Today


Thread: Ken's 1989 YJ Project Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-27-2011 02:52 PM
plcprog
Ken's 1989 YJ Project d

The engine had little power. The timing was way retarded and the jets in the carb were mixed up. I also drilled the main jet out a little. Still not much for power but it will get down the road. I am afraid to go over 70 with it.

Attachment 39504


The only frame rust was in the back. 1/4" flat stock took care of that. Why did they put the holes in the frame so water and dirt could get into it and rust it out? I plugged them up.

Attachment 39505

Attachment 39506



I now have a good running $4500.00 Jeep that cost me about $5800.00. Jeep Jamboree here I come.

Attachment 39507
02-27-2011 02:43 PM
plcprog My homemade truss. Dana 35s are known for bending and braking. This 3/8" x 8" x33" flat stock, cut to fit and welded onto the axle, should help.

Attachment 39490


After I cut it to fit, I drilled holes in the plate and used muffler clamps to clamp it to the axle. Then I heated the right axle tube to strighten it, the clamps strightened it once it was hot. Once in place I welded it. The pumpkin is of coarse cast iron. I heated it up with a torch first, not too hot, then welded it with cast iron rod. Standard rod can be used to weld to the tubes. I left the clamps on too. Because of the 3.5" spring lift and the 1" body lift, there is plenty of room for the $45.00 truss. The trac bar is now gone.

Attachment 39491

Attachment 39497


The B&M ratchet shifter works good with the manual valve body on the transmission. I made both shifters longer.

Attachment 39498




02-27-2011 02:33 PM
plcprog
Ken's 1989 YJ Project c

Chain steps are for my wife. I matched the paint to some Rust-Oleum spray bombs. Paint repairs are now easy.

Attachment 39485


The 9500 lb Warn winch is courtesy of my son. The mount was for an JK, some cutting and welding made it work. The brush guard came with the Jeep but was not on it. He said it got in the way of the tow bar that also came with it. I just moved the tow bar mounts down. I use the tow bar to tow it behind our fifth wheel.

Attachment 39486
Attachment 39487


I am always afraid I will back into something and cave in the tailgate with the spare tire. This should stop that from happening.
Attachment 39488

Attachment 39489


I found everything on ebay to change the gears from 3.07 to 3.73, with posi in the back. I don't know how anyone could do a job like this without ebay. A lot of little things, and some big, came from ebay.
02-27-2011 01:57 PM
plcprog
Ken's 1989 YJ Project b

The shifter and floor were all cobbled up. One $35.00 radio and we have music again.
Attachment 39482


More rust. I bought all 4 floor pans and welded them in. The floor was painted with brush on Rust-Oleum black hammered look paint.

Attachment 39475


Transmission fluid. I had to have the transmission rebuilt.

Attachment 39476


The top and doors came with the Jeep. They only needed some paint.

Attachment 39477


The 33" tires from Craig's List. $350 for all four. They are like new.

Attachment 39478
02-27-2011 01:47 PM
plcprog
Ken's 1989 YJ Project

Ken’s 1989 YJ Project

When I got this YJ it had a good motor, lift, rims and a lot of rust. If I saw all the rust it had, I would not have bought it, but then I would not have the Jeep I have today.

This looked solid when I brought it home.
Attachment 39470


I started by replacing the floor and rocker pannels. The rocker pannels are 4"x6"x1/8" angle I made from flat stock. I also welded in some small angle, on the inside, to stiffen it up. I also tied the angle into the body mount. You can now jack up the side of the Jeep using the rocker pannels.

Attachment 39472


All the bottoms of the door frames had to be rebuilt.
Attachment 39471


When doing this kind of work on the body, you have to carfull not to shrink the door openings or your doors will not close. I did ok on the drivers side but on the other side I had to use a bottle jack and open up the door openning.

Attachment 39481



As you can see the engine is clean. I found out that it is at least 2 years older than the jeep. You can tell by the oil filter it takes.
Attachment 39473

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:41 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC