Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > General Jeep Discussion > Spider Gear Trouble

Join Wrangler Forum Today


Thread: Spider Gear Trouble Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-14-2011 10:34 AM
Tyewilly If you haven't already, try removing the wheel and brake drum. It may be that the shoes are hanging up in the drum and not letting the axle shaft move far enough. If that's not it, you may have a twisted shaft.
03-13-2011 05:04 PM
Thesnufalufagus It's not wanting to slide enough for the clip to fall out for some reason
03-13-2011 04:57 PM
herbie no once you have the cross pin out the axle should slide in so the c clip can clear the axle gear then that clip should almost fall off
03-13-2011 02:47 PM
Thesnufalufagus The spider gears are gone,but I'm now having trouble removing the c-clip on the drivers side.I've tried everything save beating the shaft with a BFH anyone have any idea as to what is wrong?
03-12-2011 11:49 PM
turdhurdler This is also a great time to replace the stock spider gears with a locker like Lock Rite or Aussie. If you are at a 33 or smaller tire the axle should hold up fine. Good luck with your project.

Jeff
03-12-2011 10:55 PM
Thesnufalufagus Great!Thanks for the fast response this should save me a couple hundred.
03-12-2011 10:42 PM
distortedtj here is a little better step by step...

1) remove the center pin bolt with a 12point 8mm BOX end
2) tap out the center pin slowly till you can grab it and pull it out of the carrier
3) pull the C clips
4) pull out the axles about 3 inches, you can leave the rims and tires on them.. ive done it too many times
5) remove all the gears, make sure you take the spider shims too, dont leave them in
6) replace and reverse the above for installation
03-12-2011 10:35 PM
distortedtj yep. Once you pop the cover...remove the center pin. then come right out...put new in.
03-12-2011 10:24 PM
Thesnufalufagus So I've narrowed down my problem to the spider gears and I will pull the cover tomorrow to confirm this.Question is can an average joe with a bit of shade tree mechanic skills and a set of sockets and hand wrenches replace them?
Dana 35
3.07

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:06 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC