Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > track bar help

Join Wrangler Forum Today


Thread: track bar help Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-13-2011 09:14 PM
neverfastenough1 I had a time with that, too, but a hammer and a fork popped the ball joint out without damaging the boot for future reference.
03-13-2011 08:12 PM
whitejeep I soaked it with PB Catalyst, tapped it with a hammer and repeated every 10 minutes for about a hour. Then used my floor jack to compress the suspension. I set the end of my crowbar on the top of the bolt with the crowbar perpendicular to the bolt. Then with my dead blow hammer, smacked the hell out of it. I used the crowbar so I could get a good swing at it. I was hard getting a good hit on it where it was located. I am now the proud owner of new front adjustable track bar and JKS disconnects.
03-13-2011 02:54 PM
Wheel2Work Did you smack the mount with the hammer instead of the track bar end? That usually frees up the end, as it allows the conical hole to elongate a little bit...

Presuming it was the front track bar
03-13-2011 02:03 PM
GroundHawg what did you do?
03-13-2011 01:56 PM
whitejeep I GOT IT!!!!! Seeing the track bar fall out was almost better than sex........almost.
03-13-2011 01:50 PM
GroundHawg Oh

If it's got a pin, cut it flush. Now put the nut back on and twist the hell out of it to break that dirt and rust up. Then try tapping it out
03-13-2011 01:38 PM
whitejeep I've got the nut off just can't get the bolt to slide out. I put my 3' crow bar on it and it doesnt move. Can't really get a good hit with a hammer on it good because of its location.
03-13-2011 01:32 PM
GroundHawg Try the breaker bar, if that doesn't cut it put a cheater on the breaker bar. If that doesn't work try to see if an impact gun will get in there.

If no dice still, light it up with a torch and breaker it. Use caution though. You don't want to combust the Kroll or Blaster you sprayed all over it
03-13-2011 01:24 PM
whitejeep I've given it hell but nothing. I have the wheels off though. Is that maybe putting the bolt under more tension and not causing it to move? Should I put the wheels back on and set the jeep on the ground and try again. Or do I just need to man up and get the bolt out?
03-13-2011 12:59 PM
Jerry Bransford Use a long breaker bar on it for more leverage.
03-13-2011 12:35 PM
whitejeep
track bar help

I cant get the track bar bolt out on the driver side. I've tapped it with a hammer, tried to wiggle it out, sprayed some lubricant around the bolt and cursed at it some. Still nothing, no movement.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:32 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC