Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Vent Selector Not Working Issue

Join Wrangler Forum Today


Thread: Vent Selector Not Working Issue Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-15-2012 06:51 PM
starramus
Quote:
Originally Posted by bmanrkg3 View Post
I had the vacuum leak problem too, but it was located on top of the motor on the drivers side. took a tiny zip tie and fixed it easy.
Had the same problem and I also fixed it with a nylon cable tie to keep it from coming off. They must get loose as they age, and come off.
03-19-2011 12:02 AM
bpm54 Thought about gluing but such a cheap repair, eh what the hell. I was expecting much more and got off cheap.
03-18-2011 11:06 PM
BLK00TJ
Quote:
Originally Posted by bpm54 View Post
It was a broken knob. Thanks all!
Yep. Common problem. I had two of the three cracked so I ordered three to have a spare on hand. I was able to get one working for a good while with crazy glue. Let it dry disconnected if you do this though.
03-18-2011 10:47 PM
bpm54 It was a broken knob. Thanks all!
03-16-2011 09:37 PM
bmanrkg3 I had the vacuum leak problem too, but it was located on top of the motor on the drivers side. took a tiny zip tie and fixed it easy.
03-16-2011 04:39 PM
darin.1701 i have an 04 X and the "tab" thing on the knob broke. it was a simple fix, went to the dealer, spent $5.00 bought a new knob, installed it in the jeep, and it was working again.
03-16-2011 02:59 PM
FamilyGuyJeep As for the selector not working, check the knob itself. At one point the back tabs that keep the dial centered were broken and all I needed were new knobs. Mine would spin all over the place. The cold issue could be a thermostat. Not quite sure what the clicking in the engine compartment might be without hearing it. Just some other options if the others didn't work. Good luck.
03-16-2011 02:43 PM
TexasT Probably vacuum, as mentioned...the default mode or no vacuum mode is defrost.
03-16-2011 02:31 PM
02tjapex I had the exact same problem in my 02. Turned out it is a vacuum line that controls the vent selection. Look underneath your battery tray and you'll see a black plastic box with 3 or 4 rubber hoses coming out of it. Make sure everything is connected. Worked for me. Let me know.

Sent from my iPhone using WF Access
03-16-2011 02:02 PM
wmpiehl sounds electrical to me, like your switch has gone out. It may also be the doors in your heater/AC box. That was my problem. If one of those breaks then you usually only get air out of one vent. The blower will still work thought. The broken door trying to move may be the clicking noise you hear.
03-16-2011 12:11 PM
bpm54
Vent Selector Not Working Issue

I have a 04 Wrangler and recently I've lost control of the vent selector. I can't select AC or direct air venting. When turning the vent selector knob it doesn't click from each setting to the next. The blower seems to be working fine in the sence that you can hear it as you turn it up from min to max but no air will blow out of the dash vents. Also, cold air seems to be coming from the defrost vents all the time now.

Also, about the same time this started to happen a clicking noise is present in the engine bay. The noise will occur about every 30 seconds.

Any Suggestions as what the problem is and how to fix.

Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:27 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC