Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Inexpensive Hi Lift Jack mount

Join Wrangler Forum Today


Thread: Inexpensive Hi Lift Jack mount Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-20-2013 08:20 PM
gasf3 Thanks for the info!
05-20-2013 07:59 PM
my996duc1 Mounted mine on the roll bar just the same as the OP.
Out of view and protected under the soft top.
I bought the taller High Lift and then cut it off to get the maximum height that would fit inside.

_
05-20-2013 07:47 PM
Patrick H You should put a cover on the mechanism. It's going to get full of dirt, mud, etc., and they WILL kick your ass when they aren't clean and lubricated. I watched my Brother get hit in the head and knocked out cold by a high lift handle when the jack malfunctioned due to the mechanism being dry and dirty....
05-20-2013 07:06 PM
callbob nice and shiny though
05-20-2013 06:44 PM
gasf3
Quote:
Originally Posted by Trailsnail View Post

Uhhhhh, doesn't that kill your departure angle?????
Not really. It looks a lot lower than it really is
05-20-2013 06:38 PM
callbob Although I have an LJ and more room, I mounted mine in the back with the bottom on the floor and the top on the opposite fender. The bottom plate is sitting on a rubber pad and the top is also. I drilled a hole in the fender well, hooked a j bolt that comes up through the jack frame and fastened with a wingnut. Tight, doesn't rattle and out of site out of mind. Only thing is I will probably never use it and have had this jack for probably 40 years. It will be coming out for that reason. I am going to invest in a air lift dealio that inflates with exhaust air or compressor. I saw a video on it somewhere and much more versatile and 100% safer.
BYW total cost was $1.00 for rubber pad and 2.49 for J bolt washer and nut.
05-20-2013 06:35 PM
Trailsnail That's just shy of being a plow
05-20-2013 06:33 PM
Trailsnail
Quote:
Originally Posted by gasf3 View Post
I welded a piece of 1/4 inch steel plate to a cut off trailer hitch and put a bolt and nut through it. here is the result.
Uhhhhh, doesn't that kill your departure angle?????
05-20-2013 06:21 PM
gasf3
Another Creative spot

I welded a piece of 1/4 inch steel plate to a cut off trailer hitch and put a bolt and nut through it. here is the result.
04-05-2011 11:51 PM
Firemangully lovemachine - it's very easy, cheap, clean, and secure!

jeepers29 - thanks, your welcome.

Firemedic730 - I want to say it's the:
Stanley-National Hardware 526 U Bolt SS Item #: 252476 Model #: V2193 $3.67 from Lowes

Chocolab - your right! Where is the emoticon of pistols when you need one...
04-05-2011 11:37 PM
Chocolab Nice idea but the tire cover is even better..... WRECK EM'
04-05-2011 09:40 PM
Firemedic730 What size u-bolts did you use. Just got a high lift Jack and really like where and how you mounted yours.
03-21-2011 07:14 AM
jeepers29 Nice! Thanks for the idea.
03-21-2011 05:20 AM
lovemachine I bookmarked this page. That's exactly how I want to mount mine.
03-21-2011 04:09 AM
Firemangully To clear up some confusion on exactly where this is mounted.
03-20-2011 11:22 PM
Firemangully Like rubicon05 said, it doesn't interfere and actually covers it up from opportunistics.
03-20-2011 09:34 AM
rubicon05 Thats were i run mine also, and no it dosent get in the way of the soft top. actually covers it up when the soft top is down so no one can see it in there.
03-20-2011 05:30 AM
jeepers29 I can't tell where that is. Is it behind the back seat going side to side? I like.

Never mind, I figured it out, but won't that get in the way of the soft top when it is done?
03-20-2011 05:04 AM
Firemangully
Inexpensive Hi Lift Jack mount

Hello all, I just wanted to share a tip for mounting the jack in case you were still on the fence on where to put yours. After much debate and many threads read about mounting locations, I decided to mount mine inside and out of the elements. I decided against the hood mount, front bumper mount, and rear bumper mount. I appreciate all the help and pics leading me to my decision.

The base of the jack rests on the tub just behind the rear of the roll-cage on the drivers side. This mount secures the jack utilizing 2 u-bolts, 6 nuts, 6 washers, and 3 wing nuts and took me about 15 minutes. All items were purchased at Lowes for about 8.00.

So if your looking for a cheap, secure, and easy to do mod for mounting your jack; this one would be hard to beat.

P.S. The jack is accessible in about a minute and a half-not that your in a hurry, usually when these are used, your stuck!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:42 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC