Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Oil pressure gauge pegged.

Join Wrangler Forum Today


Thread: Oil pressure gauge pegged. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-21-2011 06:26 PM
yjrestoinprogress ok thanks guys ill try it and report back
03-21-2011 03:46 PM
kik My 89 4.2 sending unit has one wire and is in the shape of a bell for a lack of a better term. I replaced mine 3x. They seem to work fine for awhile and eventually peg out. Most times mine works great after everything warms up.
03-21-2011 03:19 PM
Undead-89 Okay here are the results (done with the key in run, engine not started):

If you take a wire and short the two contacts together on the double prong unit, it sets some relay in the engine compartment but the gauge does not change.

If you run a wire from the lead going to the single prong unit to the chassis ground, it will cause the gauge to go to zero.

So the one you need to replace is the single prong one. (as do I, these used to cost 60 bucks, I think I will replace it now that it is reasonable.)
03-21-2011 03:05 PM
Undead-89 According to that page, the two prong one is for the idiot light and the single prong one is for the gauge. I'm gonna go double check mine.
03-21-2011 02:55 PM
yjrestoinprogress My block has both of these on the right side of the motor Oil Pressure Switch | 1990 Jeep Wrangler 4WD 6 Cylinders T 4.2L 2BL | AutoZone.com the one with two prongs has a BLUE/WHITE wire and an Orange wire in it the other one has a single red wire? The red and the orange wire are hot at all times
03-21-2011 11:25 AM
Undead-89 There should only be one Oil sender unit. near the rear of the engine on the Passenger side if I remember correctly. The wire should be Light Blue/green.
03-21-2011 10:47 AM
yjrestoinprogress sorry guys i forgot to put that in there its a 1990 yj with the 4.2 in it. i bought it with a blown motor so i have no idea how the wiring was before i pulled the motor
03-20-2011 07:41 PM
NAVYCHIEF what engine and year? on my 4.0 the sending unit is on the rh side. the wire is gray/yellow stripe.
03-20-2011 06:28 PM
yjrestoinprogress even with all the wires disconnected the gauge still stays pegged at high. which of the sensors control the gauge?
03-20-2011 04:03 PM
NAVYCHIEF what does the gage do with both wires disconnected?
03-20-2011 03:34 PM
yjrestoinprogress
Oil pressure gauge pegged.

Hi all, I just got everything on my motor back together and for some reason the oil pressure gauge is pegged high. Now there are two sesnors and I know a bad one could do this the one sensor has a blue and white stripe wire along with an orange coming out of it. the other sensor has a single one with just a redplug in wire on the top of it. Which on controls the gauge? If I put a test light on the sensor with the single wire on it the single wire will read hot with the key on. The blue wire on the other doesnt do anything when hooked to ground and the orange will read hot just like the other sender. Also none of this has any effect on the gauge reading.
Thanks dan

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:13 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC