Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Builders Corner > My Low budget quick stock bumper mod!

Join Wrangler Forum Today

Thread: My Low budget quick stock bumper mod! Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-28-2011 06:41 PM
GoldenSahara00 Sweet man post a link on here when u do
03-28-2011 01:20 AM
SUBZEROCOOL Nice, I'll post mine soon.
03-28-2011 12:41 AM
GoldenSahara00 Thanks ! and it was a pretty easy mod. it would be better to get metal plates cut and welded, which shouldnt cost you more than 50 bucks total less if you have your own welder. if not take it to a muffler shop or someone you know. you can get a metal shop to cut you some pieces cheap. I just wanted to do it as cheap and home made/self relied as I could! saving for my lift and every buck counts haha. I can finally order tomorrow
03-27-2011 03:16 PM
Cadillaccarl85 I dig it,looks cool,been tempted to try something like this since I bent in my passenger side
03-27-2011 03:10 PM
Michaellkemp Looks great man!
03-27-2011 10:42 AM
GoldenSahara00 Thanks man. It was def worth it, got my old tubes off and sold them, and the new ones cost me 5 bucks.
03-27-2011 03:59 AM
rivera82 good and quick mod, looks good man
03-26-2011 10:20 AM
GoldenSahara00 No, I used putty to keep it in place and then just filled over the top of the hole anda to the sides on the front. then flip over, pull the putty back(once JB is dried) and do the same to make sure its holds. then sand. if you sand it to fast or low you may get some tiny holes that need filled. it seems good as a filler. As for holding the ends on, it does alright but if it takes a direct hit on something the end will pop off Im sure. its not metal. But hey Id prefer plastic popping off over bent metal!
03-24-2011 10:04 PM
JeepinDave how does the jb weld hold up as a filler? did you need to put any metal or anything on the backside for the jbweld to adhere to?
03-23-2011 10:13 PM
GoldenSahara00 Thanks mike! yeah, I may end up throwing on two more anyways, but for now im happy with it.
03-23-2011 10:11 PM
M_ M is for Mike haha, anyway I kind of like the lights out there it's different
03-23-2011 10:09 PM
GoldenSahara00 I wanted to put the fogs in the middle, and drilled holes but theres not enough room to get the nut for the bolt in between the fram and bumper. So I think I may add some tabs to itif I can get a flat head bolt under or something. I just dont like the look of the fogs out there.
03-23-2011 10:07 PM
GoldenSahara00 Thanks! I knew I needed something creative since my pockets are pretty shallow! haha. and thanks M it looks alright, my first time doing a bumper.
03-23-2011 10:04 PM
M_ Good job, man final product looks really professional!!!
03-23-2011 10:02 PM
perkalator It looks good. Nice creative thinking.
03-23-2011 10:01 PM
GoldenSahara00 finished
03-23-2011 10:00 PM
My Low budget quick stock bumper mod!

Basically I used my stock bumper, cut the ends down angled, drilled an extra set of fog holes for future use, filled all the holes on the front, including those from the rubber pads I removed, and made end caps out of heavy duty plastic. sanded and bedlined. its not perfect, but I already had the bedliner around, had all the tools and the plastic. the only cost was $5 for JB weld which is a epoxy/liquid weld glue that I used to fill the holes and attach end caps. I used plumbers putty to hold the JB weld from running through the holes, filled them is several coats over several days. this was perfect as I only had an hour max each day to work. I think it turned out well, and looks good. allowed me to remove my tube bumpers, and hopefully sell them to help get some money towards my lift I also did the rear but I have no pics yet.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 08:11 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC