Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Builders Corner > Ford 8.8 swap

Join Wrangler Forum Today


Thread: Ford 8.8 swap Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-30-2011 04:36 PM
TheTJRod I don't think this belongs in the Fab section. This is more of a question for the TJ section.

BTW, I just bought all the brackets to get a ford 9 in my TJ and it was just about $200 shipped. From ballistic fab. Get a digital angle finder a few good measuring tapes and look at Stu Offroads 8.8 swap page for exact measurments for all the mounts. Also a great thing to get with half of it lined up for you is a rear axle truss from TnT Customs The UCA mounts are prewelded to the truss, then just use an angle finder after you set your pinion angle to weld on the coil buckets and LCA mounts.
03-30-2011 12:39 AM
foxinthemudd I bought mine from ECGS (east coast gear supply) and I do have to say it was well worth it. fully set-up with lockers and gears plus disk brakes. easy install just remove the old one and install the new. If you can swing the cash its more than worth it. I had considered doing it myself but it would have taken a ton of time to do and I don't have a lot of time on my hands with all my other projects and work getting in the way.

D44's are hard to come by these days, and are usually around the same price range for a good one. just something to think about...
03-25-2011 09:50 PM
97wrangler-242 I'm in central Indiana and I'd b willing to build my own but I'm so worried about getting the brackets on right. I'm not great at welding
03-25-2011 05:31 PM
POS YJ FORD 8.8 TJ BRACKET SWAP KIT
Ford 8.8 FOR SALE- $150.00 O.B.O. - Pirate4x4.Com Bulletin Board
Not sure of your location, but there are several companies that make these swap kits. I've heard some are as cheap as $175, but this was the best I found. You can find the axle itself at most junkyards or in the for sale forums. Try the vendors on here as well as the sight from my second link. Many will give discounts if you are a member of certain boards. DO NOT post in the hard core section over on Pirate, they will tear you a new one! They will offer friendly advice in the newbie section though. Where are you located?
03-25-2011 04:03 PM
97wrangler-242
Ford 8.8 swap

I'm looking for the cheapest way to put a ford 8.8 in my tj. The east coast gear supply goes over a grand by the time you put everything in their empty housing. How hard is it to weld your own brackets on? I just need a new rear end fast and cheap and do not wanna mess with the Dana 35 any more. Mayb a cheap rubi 44? Or someone selling a 8.8 at a decent price ready to go. Looking for 3.55-4.10 ratio

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:10 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC