Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Jeep Wins - I Quit

Join Wrangler Forum Today


Thread: Jeep Wins - I Quit Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-05-2011 08:55 AM
erickpl man44a, I agree that the pass side of the 2.5 is a big PITA. The driver side on the 4.0 is the PITA (I've done both). The hard part is the way the bolt faces. There are things in the way.

What I did - I didn't remove the bolt on the mount. I left it in place, but VERY loose. I had not done the driver side yet, but I loosened it too. I also loosened the transmission mount from the skid plate and removed the fan shroud and left it hanging on the fan loosely. With everything loose (and the TJ on the ground!), I jacked up the engine/transmission enough so that I could rotate the passenger side mount up, add the bolt extension, then fit it through the MML block (I'm assuming you have the MML blocks from Dirk since you mentioned DPG). Yeah, it jacks the engine up a bit, but just rotating it up high enough lets the bolt go in. With it up that high, I set the driver side MML block in place too. I lowered the engine just a tiny bit at a time to ensure everything lined up properly (had a hand watching one side while I did the other and controlled the jack's down speed.

Worked fine.

Just think it through slowly. There IS more than one way to get that stuff together.

04-04-2011 07:46 PM
stanger04 I always tell my fiancee it will only be a couple hours but ends up all day. Better to take longer and know it's right than just throw it together. Also look at the broken bolt as an opportunity to learn how to use an extractor, which is a very useful tool when owning a Jeep.

Try and finish, worst case after you are done take it to a shop for a double check. Also when in doubt ask, easier than breaking and fixing, I did when I did a shackle lift. I left it for the day asked the people on here and got some of the best advice I could ever get. My lift is on and the Jeep runs great best of all labor only cost me a few bloody knuckles,lol.
04-04-2011 07:38 PM
wmpiehl Just take this as a lesson that nothing will go as planned when you do new things on your Jeep. Always budget extra times and maybe enlist the help of some Jeep buddies.
04-04-2011 07:33 PM
05wrangler well that is a good thing. glad to here. are you goin to attemp to do it again?
04-04-2011 07:19 PM
man44a Thanks for the encouragement. On a positive note, things did go back together easier and much faster than coming apart.
04-04-2011 06:10 PM
05wrangler yep just keep tryin, one step at a time. make sure to look things over. another set of eyes and hands are nice to. and always remeber people are here to help goodluck!
04-04-2011 06:09 PM
Firemangully I agree with everyone here, take a break, some deep breaths, and try again later. You will appreciate it that much more after overcoming the "obstacles"!!
04-04-2011 06:03 PM
KBR97 Oh BTW...I think a big part of your problem is that you overwhelmed yourself with quite a few different projects all at one time, and tried to do a little of each.
Just focus one one thing at a time. If you get annoyed take a break...not a break doing something else on the jeep...I mean a break from the jeep completely..go have a sandwhich, drink a beer, walk the dog, boff the wife or GF....just something to get your mind a way. Come back clear headed and relaxed and re-assess the situation.

When I did my motor mount spacers the one side when it fine..I spent the next 3 hours playing around with the opposite side. I decided to quit and try again the next day.
Took me about 10 minutes to get it in the next day.
04-04-2011 06:01 PM
sdxmiller never quit. maybe walk away, have a couple of beers.
04-04-2011 05:58 PM
devous1 Welcom to the mod world. Jeep parts in my experience are pretty easy to get at in my experience. I have a couple Mystangs you cant get your hand in anywhere. With that said, I agree with the others, if you get frustrated just take a break, get a drink. Move onto the next item on your list and come back to the problem later. It will give you time to cool down, give you time to consider other options to accomplish your goal, and if you complete another item on your list the sense of accomplishment will restore you positive attitude.
04-04-2011 05:54 PM
ou812 stright from the repair manual heres the torque specs
Tighten the cover bolts to 41 N-m (30 ft. lbs .) torque.
as KB stated its not gonna hurt anything for now
04-04-2011 05:46 PM
KBR97 You dont wanna change motor mounts with the jeep up on a lift. Its better/easier to do while its on the ground. This way you can get a floorjack under the engine and lower or raise the engine whenever needed. And a big pry bar helps to move the motor around when it gets a little stubborn.

As far as the broken bolt in the diff...you said its on the top of the cover right? Just leave it for now, and finish the rest of your lift. Its not gonna leak or fall off or anything. Don't wanna sound like I'm telling you to never fix it but even if you forgot about it... probably would never cause a problem.

The upper shock nuts seizing up is just something that comes along with the Jeep.

Get the rest of the lift in the Jeep. Then do the body lift, then the motor mounts, and then worry about the broken diff bolt last.
04-04-2011 05:04 PM
SilverTJMike 30lbs is the fsm spec. Talking to riddler they said 20lbs is fine. Lubelocker gaskets specify 35lbs, so i compromise somewhere between 20-25 if using factory bolts or grade 8.
04-04-2011 04:27 PM
MikalCarbine 30ft-lbs sounds excessive for the diff but I could be wrong
04-04-2011 04:18 PM
ou812 doing your own work can be a bumpy frustrating road but for us under paid people its our only option

I just looked at my motor mounts,It doesnt look too hard to get to,im assuming your bolts are just very tight

if the motor bolts are the stuck ones spray it with pb blaster warm the engine up to normal temp and then try,Its an over and over process until it comes out.

try putting a wrench on from the bottom hold the wrench and tap the wrench with a hammer,a hammer tap can put out far more than your arms

hang in there and take breaks....have a Beer man.Sometimes we just have to walk away and take a break.it cool though that you now know why the shops charge so much.

Goodluck and please try again,let us know exactly what your problems are
maybe you have the wrong tooling

as far as that broken bolt I would drop the rear axle instead of the tank,use an easy out extractor.Hopefully the bolt broke due to stress and not cause it bottomed out,if it broke from stress sometimes a center punch can unscrew it cause its hand tight.Ive used the left handed drill bit alot too,just start small and slow

also make sure the bolts are tightened to the correct torque,sometimes people confuse inch pounds with foot pounds
04-04-2011 04:00 PM
man44a
Jeep Wins - I Quit

So...

I decided to start lifting my 97 TJ 2.5l and thought while I was at it I would do some basic maintenance. I have access to a lift and shop space but have very little experience doing any work. I ordered the DPG Ultimate OME kit with the upgrade to Brown Dog motor mounts. I also bought an OME steering stabilizer so they would all match. Ordered Riddler diff covers and painted them. Started with self etching primer, then 4 coats of a Metallic Nickle(jeep is silver), then about 10 coats of non gloss clear. They look great.

Once on the lift I noticed my exhaust looked like someone may have changed it. It also was the only rust under the jeep. I used a high temp brush on paint and put several coats from the down pipe all the way to the exhaust tip. No one will ever see it but me, but it made me feel better.

Started removing the front shocks and springs. The upper shock bolts would not loosen even after PB Blaster. Used a dremel to cut the nut and was able to remove them. Springs off both sides no problem. Took longer than I expected but I got it.

While I had wheels and shocks/springs off I decided to try and change the motor mounts and add the body lift. I was able to get the drivers MM off but just cannot get the passenger side. read on here, tried the tricks I could find. just cant get it.

Frustrated now by the passenger MM, I decided to move on to something else and come back to it...

The rear D35 I noticed was leaking. Fount it had a bent cover. When I removed the plug dark thick black oil came out. Gross. Who knows when it has been changed. I ordered a Riddler cover to replace and it is beefy. Very impressive. However, the bolts they supply suck. When torquing it down to 30lbs as directed, several bolts crushed the lock washer and 1, high up, snapped off in the diff! Cant access it because of the gas tank.

Passenger MM cant get off, broken bolt in rear diff. Im done.

I put the springs back on to support the front and now plan to take it to my local offroad shop to finish it off. Just so frustrated.

Long story short, these lifts are not as easy as they seem. 8-10 hours is crazy for a novice/first time installer. Riddler bolts suck.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:58 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC