Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Problems after tune up

Join Wrangler Forum Today


Thread: Problems after tune up Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-28-2011 07:23 PM
gmaak Have you just checked the plugs? Something similar drove a friend nutts for a month after a basic tune up and all it turned out to be was a bad plug. Not to familiar with the YJ but can you pull any codes. Like you said everything was fine until you did the tune up so start with these areas first before jumping to conclusions. Just my 2 cents.
04-28-2011 06:46 PM
Brecko69 I moved the wires one spot over in each direction and the engine did not even start. The firing order is defiantly correct.

The thing is, it only stalls out when put into gear before it reaches about 150degrees on the temp gauge. And once it is fully warmed up to about 210, it idles perfectly at 600rpm....doesnt even drop in rpm at all at idle.

This is making me think it may be a choke problem.

Any thoughts??
04-12-2011 02:25 PM
POS YJ There was a guy on here a week or so ago with a similar problem, and he had 2 or 3 different plug wire diagrams for his jeep. The firing order should be the same, but the location of the wires on the cap was different. Try moving all of the plug wires clockwise 1 terminal on the cap and try it. If that doesn't work, then move them back 2 places counter clockwise, or 1 spot CCW from where they are now. I'm guessing that this will fix the problem, as when you disconnect the vacuum advance, it adjusts the timing enough to run o.k., but not correctly.
I will go look at my cap and let you know how mine is set up.
My #1 plug wire is right in the middle of the 2 cap mounting screws, facing the PS motor mount. Mine is the 4.0 though. I'm assuming yours is the 4.2, not sure if it makes a difference, but I would start rotating the wires. Keep us posted.
04-12-2011 01:56 PM
Brecko69 POS YJ,
I did not replace the wire one at a time, but I did go over the firing order and made sure it was correct. I also tried putting the old wires back in to rule out the new wires being bad and had the same problem.

GaryK,
I will check for a vacuum leak. I would agree with adjusting the idle but, it idled fine before the tune up so I dont want to up the idle to mask the problem.
04-12-2011 01:36 PM
Garyk If it stalls when put in gear with an auto yet runs and idles fine then I would suspect the idle is too low or a vacuum leak
04-12-2011 01:03 PM
POS YJ Did you replace your plug wires one at a time? If you unplugged the vacuum advance and it didn't stall, I would look at the plug wires.
04-12-2011 12:49 PM
Brecko69 I double checked the firing order and that was all good. The wires are hooked all hooked up tight as well.

The jeep is a automatic and it stalls as soon as you put it into gear.

I did unplug the vacuum advance and it did not stall when put into gear....
04-11-2011 09:47 AM
sevenservices be sure you put the small piece in under the cap to that goes down to the top of the rotor. It looks like the end of a pen or something about half an inch long. They will run without them but the spark has to jump... Just something to check. If you still have a piece left over that looks like that, that would be it.

Does it stall when you put it in gear or when you start to let out on the clutch? Parking brake isn't on is it?
04-09-2011 10:51 AM
Garyk Make sure fuel filter is installed correctly, plug wires in proper sequence, plugs gapped correctly. All wires properly seated, especially at coil, I have found defective rotors before right out of the box, the carbon button inside was missing/damaged.
04-08-2011 02:14 PM
Brecko69
Problems after tune up

I just gave my YJ a tune up and now when I put it into gear it stalls out. It was not doing this before. I did not adjust the timing or anything, just the regular tune up: Dist cap and rotar, plugs, wires, fuel filter, and PCV valve.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:42 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC