Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Can't shift? HELP

Join Wrangler Forum Today


Thread: Can't shift? HELP Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-18-2011 05:05 AM
puffisaurus i got mine totally replace for under 500. clutch is still a lil soft, but it runs like a champ again.
04-17-2011 02:38 PM
joseph.vallely I know that I was having the same problems and was told the same thing. But then the other night I was driving home and everything felt fine and all of a sudden I heard what sounded like a snap and something spinning around. Turned out that my clutch completely went out and couldn't go anywhere. So I would suggest to anyone else that if you are having this problem to go ahead and replace your whole clutch while you're at it and maybe even your flywheel. It'll save you the cost of having to pay for a tow truck to get your jeep back home or to a shop if you don't think you'll be able to do it yourself. Also, though my transmission would have it's good days and bad days. Some days it would run perfectly, not grind at all and not be resistant, then others I was lucky to get it into gear even with the engine off.
So, best thing to do is just to replace your clutch and flywheel while that you have the transmission dropped to replace the slave cylinder. It'll save you a lot of trouble in the long run and it only costs about $300 if you shop around.
02-09-2011 02:21 PM
89JEEPYJ if ur dropping the trans and stuff anyways he might as well change the clutch, pressure plate and throw out bearing
02-09-2011 12:22 PM
Bs13855
Quote:
Originally Posted by puffisaurus
my clutch is very loose... no pressure at all. it goes to the floor.
There's your problem clutch master cylinder is bad. Autozone 30 dollars about hour to install call me 9542924823 I'll walk you thru it
02-09-2011 10:27 AM
Thuone Check your fluid First. Check your bleeder screw make sure it’s tight, should be located under the jeep drivers side bell housing area.

If fluid checks out ok.. I would replace your clutch master cylinder.. Costs about 80 bucks and takes an hour at worst even with bleeding the line. Buy a Haynes manual it will walk you through the steps.

If this does not fix your problem you’re screwed! Unless you know someone that can help you drop the transmission and get to your slave cylinder assuming it’s internal. (<-Worst idea ever Jeep) If you get this far you may as well replace your clutch and flywheel if they are worn..

Good luck and let us know if you have any questions! It's all pretty easy once you have done it a few times.

87Jeep
Slave Cylinder (in bell housing)


Clutch bleeder screw


New clutch and flywheel
02-09-2011 01:50 AM
Undead-89 According to some sources that year has a sealed clutch system which would mean replacement of the entire fluid system (Master, slave and lines).

And yes it sounds like the slave cylinder went out. If it is a 258 with an internal slave cylinder/Throwout bearing you will have to drop the tranny to remove and replace the entire assembly inside of the bell housing.

In some 4 cylinder models the slave cylinder is external to the transmission and pushes on the pivot arm which is connected to the throwout bearing inside the bell housing.
02-09-2011 12:28 AM
puffisaurus my clutch is very loose... no pressure at all. it goes to the floor.
02-08-2011 08:39 PM
Bs13855 Btw how does your clutch feel when you press it down
02-08-2011 08:37 PM
Bs13855 Your buddy might be correct master cylinder. Not the brake master cylinder but clutch master cylinder. Check inside your jeep by the firewall where the clutch pedal is if there is brake fluid there like dripping down or discolored fire wall it's your clutch master cylinder. Also check to see if you have fluid inside of it.
02-08-2011 08:32 PM
Jeepin91YJ Slave cylinder in located between the motor and the tranny. Have to remove the tranny to replace. Not real hard but I would do it with a lift and tranny Jack or it is a pain. But if your changing that do the master cylinder also. All together parts should be between 140 to 200 buck depending on brand. If you get dealer parts plan on spending alot more. I just did mine a week ago and took me about a full day to. Any questions let me know.
02-08-2011 07:49 PM
puffisaurus how hard is it to replace?
02-03-2011 09:35 AM
sevenservices master cylinder is for your brakes... Its the slave cylinder that works your clutch.
02-03-2011 01:22 AM
puffisaurus fluids are fine...

i was told by a buddy that it is a master or slave cylinder.
02-02-2011 04:36 PM
89JEEPYJ u probably have a bad cluth, every light you will probably have to turn it off and you will have to bang shift without the clutch, only prob is you cant down shift soo have fun. im pritty sure ur clutch is shot though, check ur fluids and see if you can bleed the brakes
02-02-2011 12:47 PM
puffisaurus
Can't shift? HELP

So the other day i go out to my 93 wrangler and attempt to head to my trig final at school. after starting the jeep, i let it sit for a min while i ran back inside to get a book. After getting in the driver seat, i go to put the stick shift into reverse and there is a very loud and pressure feeling grinding noise. After turning the jeep off... i was then able to shift it fine into reverse. Then after in reverse i started it... and was fine, until i tried to shift. COULD NOT SHIFT AT ALL! I then turn off the jeep again... and was able to put it into 3rd gear... and thats it. i can drive it... but there is definitely something wrong with it? any thoughts guys?

thanks alot!!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:13 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC