Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Extended/CV Driveshaft on 4.5" Lift?

Join Wrangler Forum Today


Thread: Extended/CV Driveshaft on 4.5" Lift? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-24-2012 02:39 AM
Fishnhuntforever BTW you don't have upper control arms on a YJ.
05-24-2012 02:37 AM
Fishnhuntforever Either way it is a good idea to get rid of the slip yoke for off road use. Nothing will leave you stranded quicker then an empty T case. I bought the combo kit from CJ Tatton on eBay for $460 delivered. It comes with a teraflex SYE and a Tatton custom CV driveshaft. You have to shim the rear diff to get the right pinion angle with a cv anyway. It needs to point at the rear yoke on the T case.

Btw I broke the pinion yoke on my rear diff when a strap broke on me. I drove home using front wheel drive after I took the rear driveshaft off. I couldn't have done that with a slip yoke. Just something to think about. I wasn't doing anything crazy either. Just a dirt road and a few small rocks. Just something to think about.

I would go for the SYE. I had vibes with 4" RC lift and 1" shackle.
05-24-2012 12:14 AM
trent10
Quote:
Originally Posted by overthehillsahara View Post
I used a advanced adapter SYE and CV joint, did't drop the trans/transfer case and never had a problem.
Do you have adjustable rear, upper control arms? I hear you need those in-order to get your pinion angle right...
05-15-2011 08:44 PM
overthehillsahara I used a advanced adapter SYE and CV joint, did't drop the trans/transfer case and never had a problem.
05-15-2011 08:21 PM
95YamJam From Tom Woods site:

"For the Double Cardan (CV) drive shaft we have two options available."





Double Cardan is the style of Constant Velocity Joint....

Just to make things clearer.
05-15-2011 08:14 PM
ccbruin
Quote:
Originally Posted by Mortalis5509 View Post
It's a DC shaft not a CV shaft. Double carden
05-15-2011 07:54 PM
Mortalis5509 It's a DC shaft not a CV shaft. Double carden
05-15-2011 05:35 PM
banks316 I just installed a JB super short sye 300 plus shipping and had a custom cv drive shaft made for 350$ there's another option that would be way cheaper drop your trans/t-case 2 inch drop would help and throw in some shims if needed.
05-15-2011 01:31 PM
EmptyPockets I would plan on the expense. I added a 4"procomp lift to my 3/4" shackle lift. I found that the 2 degree wedge that came with the lift wasn't enough to compensate for the new pinion angle. The lift kit came with a 1" transfer case drop but it wasn't enough to get rid of the vibration.
In the end I ended up with a SYE and custom built CV drive shaft and a 9 degree wedge for the pinion angle offset. Total bill was a grand.
Just sayin, plan to spend it before you put on the lift. if you don't need it, you got extra for other mods...
05-15-2011 10:22 AM
turdhurdler You may get lucky and not need a CV shaft. Each Jeep has it own issues. Like you stated, many do not need a new drive shaft, while others cannot get rid of vibration problems without a SYE and CV shaft. 4" is where people start to see a lot of problems.

There is another member on this sight that goes by "Ibuildembig". He has done several spring over axle conversions and states that he will never use a CV shaft. You may want to contact him by PM and see if he has any suggestions. Good luck.

Jeff
05-15-2011 10:11 AM
jarradfiorito
Extended/CV Driveshaft on 4.5" Lift?

Right now I have a Black Diamond 1.5" and 1/2" lift shackles. Im thinking about running the RC 4" lift to bring my total up to 4.5". I was wondering if i NEED to change out my stock driveshaft. This jeep is not going to be used for any wheeling besides very light dirt roads. Ive heard of plenty of people not changing their driveshafts for 4"...but I wasnt sure since when the lift is new it might give me like 5 or more inches before settling. I already have my transfer case dropped. Love to hear your guy's opinions. Thankss.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:34 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC