Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Stuck Installing Lift

Join Wrangler Forum Today


Thread: Stuck Installing Lift Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-21-2011 11:05 PM
gotwood03 I just finished my 4" zone lift today took 5-1/2 hours. I marked out the hole cut the mark out and put the washer in and worked great. by doing this it just rotated the dif up and align the drive shaft a little better if you have adjustable upper you should not need to do this. I drove it about 60 miles today no vibes rides great. I did not do the transfer case drop either. very happy with this lift.
05-21-2011 01:57 AM
T2000J
Quote:
Originally Posted by burton160w View Post
So I could just skip this step and keep the bolts that came with my Currie adjustables?
yes
05-20-2011 11:58 PM
burton160w So I could just skip this step and keep the bolts that came with my Currie adjustables?
05-20-2011 11:51 PM
minderbinder3 It is strictly for alignment/camber purposes. Mainly so that the lift doesn't put too much of a bind on your control arms that your alignment cannot be adjusted. It can be offset by using the concentric bolt set or adjustable control arms. I would not worry too much about this if I were you.
05-20-2011 11:22 PM
burton160w I have adjustable rear uppers so can i simply ignore this step and adjust through my UCAs?
05-20-2011 11:13 PM
gotwood03 I am starting my zone 4" lift tomorow. I have read this part a few times to my understanding we are supposed to put an offset washer on the control arm mark out the hole and use a die grinder to offset the hole. Most likely to adjust the pinion angle to reduse vibration. I let you now tommorow if it works.
05-20-2011 10:54 PM
the idiot magnet It means that where your front lower control arm's has a rough section under the big washer and you will need to smooth it out. This is for your front lower control arms and where they mount to the axle.
Some jeeps have the washers there and I believe some years do not.
05-20-2011 10:16 PM
burton160w
Stuck Installing Lift

I'm stuck on a portion of installing my Zone 4" suspension lift.

I'm stuck on step 7 of the guide on installing the rear lift.

http://zoneoffroad.com/Instructions/J1400_J1401.pdf

Quote:
Remove the passenger's side upper control arm bolt at the axle. Place one of the provided offset cam washers between the two tabs located on the axle mount on each side of the original control arm hole. Position the washer so that the hole is closer toward the front of the vehicle and even (up and down) with the existing hole. Mark the perimeter of the hole using the washer as a guide. Remove the washer. Notice that the hole marking is located in a factory perforated section of the mount. Using a rotary grinding tool, remove the perforated section of the mount where the mark was made. Repeat this on the other side of the mount.
What does this mean???

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:23 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC