Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Question about track bar installation

Join Wrangler Forum Today


Thread: Question about track bar installation Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-07-2007 12:51 AM
jherrin215 I know it's not terrible, but not the ideal setup either. I have stock control arms, well stock everything except a 1 in BL and MML, and a small TC Drop. I have a very tiny bit of vibration in 2nd gear and I think the only thing I am gonna have to do is with the rear tracbar.
09-06-2007 07:44 PM
SavageSun4x4
Quote:
Originally Posted by jherrin215 View Post
Today I installed a set of teraflex 2 inch springs and left in my 1 3/4 inch spacers. I know probably not the best idea.
If I am reading this correctly, then you have a 3 3/4 in lift...yes?

Running a spacer with springs if fine. In fact there is nothing wrong with it at all.
09-06-2007 01:01 AM
jherrin215 Thanks AZ, I appreciate all the advice!!
09-05-2007 02:54 PM
AzTJ Yes
09-05-2007 11:39 AM
jherrin215 Jack the jeep up and put it on jackstands with the frame?? Amd do it high enough that both back tires are off the ground??
09-04-2007 03:51 PM
AzTJ No. With the rear, it would be easiest to have the axle/tires off the ground so that you can wiggle the axle back and forth.

1. Take the rear track bar off.
2. Jack the jeep up.
3. Attach the track on the axle end.
4. Measure axle location(be sure its centered)
5. Adjust track bar to length and then attach to frame.

That should be the easiest to do for the rear.
09-04-2007 10:31 AM
jherrin215 And I am talking about the rear trackbar?! Will this pull the rear around as well as the front??
09-04-2007 09:34 AM
GrnTJ Yes, thats what he is saying...
09-04-2007 09:32 AM
jherrin215 I thought you were saying center the steering wheel before you start. If i did this and the old trackbar was still installed then it wouldn't straighten anything up, that's why I was confused. So what you are saying is take the old one off then turn the steering wheel to straighten it then put the new one back on??
09-03-2007 11:07 PM
AzTJ If the axle is off the ground it will swing from side to side pretty easily.

But if its sitting on the ground, you have to push the body, more easily by turning the steering wheel. I said that twice already.
09-03-2007 09:52 PM
jherrin215 So when you adjust it out how do you ever get the bolt to start in the mounting hole? It looks like it would be too far over to get the bolt back in.
09-03-2007 09:39 PM
AzTJ You can't adjust it being attached. One end has to be unbolted.

Either with the tires on the axle and the axle on the ground... do it like I said with turning the wheels, this way the body will be pulled center over the axle.


Or you can jack up the jeep on the frame far enough so that the tires aren't touching the ground.

Either way, your going to probably have to adjust it a few times to get it close.
09-03-2007 09:33 PM
jherrin215 What I was getting at what how do you physically do it. Do you jack up the axle and get the tires off the ground, or do you just adjust it and let it pull everything around with full load on the axle??
09-03-2007 09:11 PM
AzTJ An adjustable track bar would be the best idea.

The way I try and center the axle: once the track bar is installed, turn the steering wheel the bring the body center. Drop a plum-bob off the fenders and see which way it needs to be adjusted, and then adjust it as necessary.
09-03-2007 09:07 PM
jherrin215
Question about track bar installation

Today I installed a set of teraflex 2 inch springs and left in my 1 3/4 inch spacers. I know probably not the best idea. I can definitely tell I need either an adjustable trackbar or a trackbar bracket. I was just wondering how involved the install would be? What all do you have to remove to install either one, the bracket or the whole adjustable bar?? I see how it works and how it needs to be installed, but I don't see how to get the axle centered back up once I remove the old trackbar. Any suggestions would be greatly appreciated!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:22 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC