Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > HOWTO: Alternator Upgrade

Join Wrangler Forum Today


Thread: HOWTO: Alternator Upgrade Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-19-2007 01:01 AM
AzTJ
Quote:
Originally Posted by foxinthemudd View Post
wrong person AZ thats what I'm gonna use, he was just adding to the discussion...
oops.
09-19-2007 12:18 AM
foxinthemudd thanks for the write up RK, I've always wanted one of the mean greens but could never find them for the price that I could do. maybe if I find one at a swap meet or something.
09-19-2007 12:15 AM
rketr
Quote:
Originally Posted by foxinthemudd View Post
wrong person AZ thats what I'm gonna use, he was just adding to the discussion...
yup


Don't remember what the warranty is...twas over a year ago. Alt may be different, but the howto should still work...
09-18-2007 11:37 PM
foxinthemudd wrong person AZ thats what I'm gonna use, he was just adding to the discussion...
09-18-2007 11:36 PM
AzTJ ah, I thought you were going to be using a 136Amp Dodge Ram alternator... What kind of warranty does the MeanGreen offer?
09-18-2007 11:29 PM
rketr
HOWTO: Alternator Upgrade

Did this a while back and forgot I actually did a writeup on it...
enjoy


Difficulty rating: 2 out of 5
Estimated time: 30 mins

In an effort to support all the extra stuff I keep adding to my TJ, I decided to upgrade my alternator recently. The stock alternator, from what I can tell (since I cannot find record of this particular model online) is a 117 amp Denso. After checking around a bit for the best bang, I ended up with a Mean Green high performance 200 amp alternator for my ’03 4.0L TJ. 200 amp might be overkill, but hey, that’s the point isn’t it Got it on 4wd.com for $359.99. Was the same price as a 140Amp model so I figured why not shoot for more bang...

In case you have never done an alternator swap, here’s a generic quick howto. Since there are only 4 nuts/bolts involved, it’s an easy task that really doesn’t require much effort.

Now as a caveat, keep in mind that I’m not a mechanic in any sense of the word. I just figure stuff out – computer stuff mostly – for a living and thought I’d help out other geek-chanics out there that might want to try their hand at getting a little dirty. In short, if your stuff blows up or shorts out, don’t come crying to me.

During the installation, I’d recommend that you:
1) replace the fan belt (since it’ll be off anyway). Fan belts can be found at your local auto shop and should run anywhere from $20 to $35 or so.
2) upgrade the wire connecting the alternator to the fuse box. The wire upgrade can be done by picking up 2 or 3 feet of #2 stranded cable from Home Depot or Lowes for around $0.50-$0.60 a foot and a couple of 3/8 #2 crimpable lug ends ($1.50 - $2 for a pair) from your local auto shop. Measure it out so you’ll follow the existing wire and leave a few inches of excess for engine vibration and whatnot – you do not want the wire to be tight when installed. Once you’ve crimped and heat shrinked the new wire (maybe I’ll write a howto on that too), add vs. replace it to the overall setup. By this I mean that once you reattach everything, put the old cable back in place and install the new cable on top of it. The reason for this is primarily so you won’t have to cut the wire and have a loose end on the fuse box side. Trace the existing wire to see what I mean.

During the installation, you’ll need a 1/2 “ socket wrench and a few metric sockets ranging from 12 to 15 MM.

Here’s a pic of the two alternators side by side:


The new unit is not much larger, but supplies 71% more amperage to the setup.


First thing you’ll want to do is disconnect the vehicle’s battery. To do so, remove the black / - / negative / ground lug from the battery. Then remove the red / + / positive / hot wire from the battery. For the geek savvy, Red is always FILO.

Ok, now to the replacement…



1. After the battery is disconnected, disconnect the red wire that goes to the fuse box from the existing alternator.
2. Remove/unclip the control wires (not shown) from the back of the existing alternator.
3. Remove the fan belt. Do so by using a 1/2 “ socket on the Fan Belt Tension Arm and pushing the arm toward the ground. The belt will be loose enough to slip off.
4. Remove the Connection 1 and 2 bolts from the existing alternator.
5. Pull the alternator out and set it aside.

Now, simply reverse the process.
1. Put the new alternator in place.
2. Put the two bolts in place and tighten till snug…you’ll finalize the tightening later.
3. Put the new fan belt in place by pulling the tension arm upwards. The proper bend sequence can be found on a sticker on the radiator just up and right outside the picture above. Here’s a tip: allow the smooth pulley just to the right of the alternator to be the last one that you try and put back in place. The belt won’t be tight, but it’ll be snug enough that you cannot easily get it over the ridges of the alternator’s pulley.
4. Reattach the control wire.
5. Reattach the red wire that goes to the fuse box and add the new wire that you’ve prepped.
6. Reattach the battery cables – Red first and Black last.
7. Finalize tightening the two connection bolts. Do not over tighten to the point that they strip.

After running the rig for 15 – 20 mins, recheck your bolt tensions and tighten as needed.

Now tell your wife to come and see that you did the job and didn’t blow anything up

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 06:36 AM.



Jeep, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC