Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Front and Rear Dana 44 axle values?

Join Wrangler Forum Today


Thread: Front and Rear Dana 44 axle values? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-26-2011 06:44 PM
necromancer_tat
Quote:
Originally Posted by rda616 View Post
Well, a couple things to watch for the 79 and earlier used the passenger side diff and had the smaller 260 u-joints and around 82-84 they had vacuum disconnect axles. you will have a few problems to address. The lug pattern is 6 on 5.5 on a waggy. You can use early 70's chevy spindles and mid 70's to 85 ford hubs. To get a 5 on 5.5 pattern if you want 5 lug. But either way you need new rear axle shafts because there isn't enough material to redrill the larger pattern on the 8.8 flange. You can get six lug shafts made for the 8.8 if you wanted to go that route. The brackets can be costly but I believe tnt makes a killer truss you can order with brackets already welded on for a decent price. You should also way the pros and cons. Pros are serviceable bearings, lockout hubs, steering is up off the ground, thicker axle tubes , bigger tie rods, stronger ring & pinion and better selection of gears. Cons are it's heavy, low pinion so drive shaft is closer to the ground, stock inverted t steering has dead spots and overall hurts ground clearance.
Thanks for the advice! I'll do some more research.
07-26-2011 06:43 PM
necromancer_tat
Quote:
Originally Posted by srad600 View Post
Ill be watching this thread closely and in case you sell the rear 44 Im calling DIBS...


If it isnt too hard and worth it that is.
Just so you know, the axles are old, like from 85 or previous, the rear axle is drum brakes, and it's set up for leaf springs, so it's not really worth very much... the front axle is where the money's at, but I'm curious as to weather it's worth spending 400 bucks just to have to spend even more money regearing, adding a locker, fabbing a steering set up, converting it from leaf spring to coil spring and setting it up for unpper and lower control arm mounts..
07-26-2011 06:21 PM
rda616 Well, a couple things to watch for the 79 and earlier used the passenger side diff and had the smaller 260 u-joints and around 82-84 they had vacuum disconnect axles. you will have a few problems to address. The lug pattern is 6 on 5.5 on a waggy. You can use early 70's chevy spindles and mid 70's to 85 ford hubs. To get a 5 on 5.5 pattern if you want 5 lug. But either way you need new rear axle shafts because there isn't enough material to redrill the larger pattern on the 8.8 flange. You can get six lug shafts made for the 8.8 if you wanted to go that route. The brackets can be costly but I believe tnt makes a killer truss you can order with brackets already welded on for a decent price. You should also way the pros and cons. Pros are serviceable bearings, lockout hubs, steering is up off the ground, thicker axle tubes , bigger tie rods, stronger ring & pinion and better selection of gears. Cons are it's heavy, low pinion so drive shaft is closer to the ground, stock inverted t steering has dead spots and overall hurts ground clearance.
07-26-2011 05:55 PM
srad600
Quote:
Originally Posted by necromancer_tat View Post
I've got a line on a pair of front and rear Dana 44 axles that came out of an older Wagoneer... $400 for the pair. I don't need the rear axle as I'm happy with my 8.8, but I'd like to have the front axle to upgrade my Dana 30 lp... Is it worth buying these and then spending the money to convert the older Dana 44 to bolt into my TJ? How much is the rear Dana 44 worth if I were to buy them both and then sell the rear axle?
Ill be watching this thread closely and in case you sell the rear 44 Im calling DIBS...


If it isnt too hard and worth it that is.
07-26-2011 05:46 PM
necromancer_tat
Front and Rear Dana 44 axle values?

I've got a line on a pair of front and rear Dana 44 axles that came out of an older Wagoneer... $400 for the pair. I don't need the rear axle as I'm happy with my 8.8, but I'd like to have the front axle to upgrade my Dana 30 lp... Is it worth buying these and then spending the money to convert the older Dana 44 to bolt into my TJ? How much is the rear Dana 44 worth if I were to buy them both and then sell the rear axle?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:28 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC