Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Brake Problems

Join Wrangler Forum Today


Thread: Brake Problems Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-30-2007 08:20 PM
y0diggy Thanks for all of your help guys. I cleaned and rebuilt the brake caliper, didn't help too much. So I went ahead and replaced the entire caliper and everything is working great. Once again thanks for the advice!
09-27-2007 09:37 AM
MouthfulOfGrass Yes, if the piston is frozen in the grab position and not releasing.
09-26-2007 11:37 AM
y0diggy I was able to get the tire off last night and inspect the rotors a little closer, I couldn't find a c clamp around the house so I opted not to remove the calipers...I now have some clamps and I intend to check the problem out this afternoon.

I see a couple of you guys have mentioned the caliper piston locking/locked caliper. If this were the case, would it prevent the wheel from spinning freely while off the ground?

Thanks for all the feedback thus far.
09-26-2007 08:22 AM
mud707 Had the same problem on my 01 the right brake caliper locked up and wouldn't release so I had to replace it. A new caliper is about 40 dollars at advanced auto and you'll need to get the rotor cut down or replaced if to damaged and maybe new brake bad depending how bad they are. Mine wasn't to bad so I just got it rotor cut down and used the same pads since it didn't damage them.
You may have to change the front hub/bearing assembly also wich how much it cost depends where you get it. I bought one off e-bay for 75 dollars including shipping. My cousin paid 150 for his from a auto parts store.
09-26-2007 08:13 AM
erickpl Better check the area on the knuckle where the brakes slide. If it is notched badly, then that is likely your sticking point.
09-25-2007 12:17 PM
MouthfulOfGrass x4. Yup sounds about right.

First thing I'd check is the caliper piston. If it sat that long, might've got wet before it sat and rusted up a little, enough to seize the caliper.
09-25-2007 11:52 AM
MOz X3 - pull the tire off an inspect the rotor.

You might be able to lubricate the slide pins and get by.
09-25-2007 11:12 AM
Rawkon yup i agree with the big white buffalo.

i would replace both calipers, pads and rotors. bleed the system really well and be done with it. if money is tight then do the smoking side only. save up and do the driver side soon.
09-25-2007 11:09 AM
whitebuffalo sounds like a sticking caliper and/or a hub bearing.
09-25-2007 11:06 AM
y0diggy
Brake Problems

Hey everybody, this is my first post on the wrangler forum and I have been the proud owner of a jeep for almost 24 hours now!! woot!

I just purchased a 1998 Jeep wrangler with less than 70,000 miles. It has a 3" lift, 31" tires, I6, front and rear diff locks, and a brake problem.

This Jeep has basically been sitting in a garage for the past 5 years, it seems to run good, but began smoking during a 25mi ride to a friends house and back home. The symptoms are:

Jeep is pulling to the right
Smoke was coming from the front passenger wheel well
The one rim was considerably hotter than all the others
The disc actually has two grooves maybe a 1/16th of an inch wide that have been worn out

I going to try and fix the problem after work today, but would like a little insight as to what the problem could be. I have a jeep service manual, an interest in doing this fix myself, and some mechanical know how. I just need a little guidance to get me going in the right direction.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:17 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC