Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > RockKrawler - What skid plates...

Join Wrangler Forum Today


Thread: RockKrawler - What skid plates... Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-11-2007 11:01 PM
ygohome really? Well, I checked out the skid row and it sucks. just kidding. they are pretty much the same
10-11-2007 11:00 PM
Gwjvw I just bought the skid row eng/trans skid,i checked out the medic and didnt care for it.Cant wait untill it comes in!
10-11-2007 10:53 PM
ygohome




a few more photos are in my webshots album...
http://good-times.webshots.com/album/561019075xBgMqA

more photos will get added to it later after I get the jeep on some trails
10-11-2007 05:24 PM
ygohome they are the RK ones with the built in bump stops I think. When I get it home I'll have more time to check it all out
10-11-2007 05:06 PM
Scout Which shocks did you go with?
10-11-2007 05:03 PM
ygohome I think I'll head out this weekend and see what the jeep can do I'll get pic taken, don't have any yet.

drive great on the street - so far I've only driven it from the shop to my work about 15 min away.
10-11-2007 04:23 PM
mrbigjeep x2...pics
10-11-2007 04:03 PM
Scout Perfect! Thanks for the info Ben. I'm going to get it ordered this week.


BTW, how do you like the new lift? Pics?
10-11-2007 03:49 PM
ygohome just got back from Joe's shop after picking up my jeep. The 5.5RK xfactor is installed and they did an excellent job as usual.

The "short arm" version of the jeep medic engine skid fit perfectly with the RK long arm tcase skid.
09-28-2007 09:57 PM
Scout Good point!!! I was wondering if someone would catch that jab.
09-28-2007 09:53 PM
Hackle
Quote:
Originally Posted by Simple Scout View Post
Yep that's it. That would be fine but I think I need something a little more hardcore than what Hackle and Joe have.
That is a very true comment, but if you learned how to drive you would need less protection.
Jim
09-28-2007 09:45 PM
Scout The Jeep Medic is the way I wanted to go I just wanted to make sure there wasn't a better option. I'll be interested in seeing how the SA skid works with the LA kit. I downloaded the instructions today off their website and it looks like a mod I might actually be able to do myself.

I'll wait to see how Ben's goes on before I do anything.
09-28-2007 08:57 PM
1BLKJP Joe confirmed my earlier comments today. There is no oil pan/tranny skid that will "bolt on" to the RK skid with no mods. Ben has some great advice.
09-28-2007 04:32 PM
Scout Damn that's great info! I'm in no hurry to get it done so I'll wait until yours is done and see how it goes. I'm glad you mentioned the SA skid versus the LA skid as I would have just bought the LA. Please let me know how it goes!
09-28-2007 04:25 PM
ygohome The jeep medic engine skid bolts in the front to the bottom of the engine mount brackets on the frame. There are a couple of pre-existing holes in the engine mount brackets that are unused that the Jeep Medic engine skid bolts to.

The back end of the skid bolts to the RK crossmemeber skid... basically, bolt up the front of the jeep medic skid loosly first... then, with a floor jack, jack up the back end of the jeepmedic skid untill the skids bolt holes are tight up against the bottom of the RK skid. Then drill your holes. Be sure the skid is not interferring with the exhaust before drilling the holes.

Since the skid is essentially bolting to the frame (engine mounts are on the frame and, of course, so is the rk skid), body lift amount should make no difference at all.

Here are the jeep medic installation instructions and they specifically reference the RK x factor lift at the very bottom paragraph.

http://www.jeepmedicfabrication.com/...irections!.pdf

if you want to wait a couple weeks I'll let you know for sure exactly how it turns out

Also, the jeepmedic skid is sold in a couple of different sizes. I have the "short arm" engine skid and I plan to reuse it with my RK long arm lift. Jeepmedic also sells a "long arm" engine skid but I think that is meant to be used only with the RubiconExpress lifts (the RE tcase skid must be positioned closer to the front of the jeep because the jeepmedic "long arm" engine skid is shorter than their standard skid). I'll let you know if I have any trouble fitting my "shortarm" engine skid with the RK long arm tcase skid.
09-28-2007 04:03 PM
Scout Thanks for the info Ben. I searched over on ROF and found some threads about some guys using the Jeep Medic. That's actually the route I'd like to go as it's basically one piece that protects both rather than two separate pieces. One thing about the Jeep Medic is I'm unsure if a BL is required. I don't believe it is but I'm still unsure. Also are there any modifications needed to the RK skid or the Medic skid to make it work other than drilling the holes in the RK skid?

Scott
09-28-2007 03:49 PM
ygohome Joe will be putting the RK 5.5 lift on my rubicon in a couple weeks (yes, he talked me out of stretching my daily driver ). I plan to reuse my existing Jeep Medic engine skid. Will require drilling a couple holes in the RK tcase crossmember skid. I know other rubicon owners whove done the same thing with their RK and jeep medic engine skid setups

the jeep medic engine skid is 1/4" and weighs about 60lbs. Covers from the engine to the tcase
09-28-2007 03:14 PM
lost never mind, scratch that
09-28-2007 03:12 PM
lost what about the nth degree oil pan skid plate.
09-28-2007 02:47 PM
Scout Yep that's it. That would be fine but I think I need something a little more hardcore than what Hackle and Joe have.
09-28-2007 02:31 PM
1BLKJP Probably mentioned the Turbo City oil pan skid to you that sticks on to the pan itself and up both sides. Great little product that has been on his and Hackles for about 4 years now and no issues.
09-28-2007 02:09 PM
Scout That would be great Jack. I talked to Joe about it awhile back but we only talked about the oil pan. He mentioned one and I can't remember the brand name. I do recall him saying that it didn't bolt on though. If I do something I'd like to cover both in one pass if that's possible.

I like armor.
09-28-2007 01:59 PM
1BLKJP I honestly don't know. I don't run one and don't know think that Jeremy makes anything. I'm going to be up at the shop this afternoon. I'll talk it over with the man and get back to you.
09-28-2007 12:44 PM
Scout
RockKrawler - What skid plates...

With the RK LA lift what are my options for a transmission and oil pan skid? Do any of the engine skids bolt directly to the RK skid? Jeep Medic? SkidRow? ______?

If you look underneath the transmission and oil pan have a big ol' bulleye on them and I'd like to cover them up.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:10 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC