|08-15-2012 09:34 PM|
|08-15-2012 08:52 PM|
just did a frame up
I just did a frame up. Minnesota Jeep and the frame was rusted through at the rear shackles. Body was rusted through on front and rear of drivers side and right rear corner. But it got worse.
I found a frame with body attached at a salvage. Included axles, etc. Once I got the body off my frame I found all kinds of little things that I got off the doner that I would have had to buy otherwise. So, if you do a frame replacement, be prepared for about $1,000 of incidentals, like brake lines, gas lines, gas tank straps, shocks, springs (mine had to be torched off), body bolts twisting off, fender bolts twisting off, radiator bolts twisting off, etc.
It took my grandson (16) and I 2 weeks to go from the raw frame to him driving it.
However, if you are using your old tub then it is quite easy. There are 10 bolts to lift the body from the frame. 5 attach the each fender to the body, along with a couple of braces. It is about 2 days to remove the body and take care to prepare things. Broken, twisted bolts could extend that time.
I would HIGHLY recommend getting a 2 ton cherry picker for about $200 at Harbor Freight. You can sell it afterwards. But it will lift the roll bars, tub, engine, etc. etc. It will assist greatly in installing the axles under the frame, etc. I painted everything as I put it back together so the cherry picker came in handy to hang the items, like the axles, for painting.
Get 2 boxes of zip lock bags, small and large. USE THEM to bag and label everything you can. The only things that don't go in the zip lock bags are things that won't fit.
Get a full set of torx sockets from T40 to T55. You will need them. And get the ones that are guaranteed. I went through three (3) T40's in one day. And the shattered, not just twisted.
I recommend Kroil penetrating. You can use google shopping and search and you could get 2 cans for about $14. VERY well worth it. Worked better than PB Blaster and Liquid Wrench, and I used all 3 extensively.
You will need a bench wire brush if you can. Need to get rid of the rust from bolts, etc. I went through about 15 cans of Rustoleum paint and primer painting everything including engine, trans, TC, drive shafts, shackels, bolts, EVERYTHING. But it really paid off when it looked like a new vehicle, except for outside I still need to paint.
Really need to people doing it to hand, hold, etc. It would have taken me at least 6 weeks to get done what we did in 2.
|08-15-2012 02:57 PM|
|jokerchief462||Too much$$$$. I saw a picture of a guys build and he had the tub on an engine hoist. That is how he removed it and put it back on. So just remove the front clip as an assembly with a freind and get an engine hoist to lift the tub. Back on same way I though it was cool the way he did it. Beats hell out of swapping a bunch of parts but you will have your share.|
|08-15-2012 12:38 PM|
|JeepMA||how much would a garage charge for a frame replacment if i already have the frame i want to put on?|
|12-01-2011 06:43 PM|
|Nubby55||Buy the 93 TheIII has down in El Paso Tx. and put your motor in it and Junk Out what's left.|
|12-01-2011 04:41 PM|
|BalooNY||Repair job pics at http://www.wranglerforum.com/f8/fram...st-125481.html|
|08-06-2011 08:59 PM|
|jfbilbro||there's a forum here for just that......selling jeeps and parts....|
|08-06-2011 08:52 PM|
|08-06-2011 08:47 PM|
|jfbilbro||and BTW, you could prolly clear that much buying the other frame and reselling it....|
|08-06-2011 08:44 PM|
|jfbilbro||you can buy the shackle sections of the frame and the frame rails, all new, from quadratec...the rails are like 100 bucks each, the shackle sections are about 120-160 bucks each, and then you have the welding cost.....prolly 700 and change in parts with new spring eye bushings and pins and i would GUESS 250 to 300 in welding costs unless you got a friend that welds.....say a grand total...that's not a bad investment on a jeep....if you decide to go that way, PM Joe at Quadratec and he'll prolly cut you some slack on the pricing and the shipping.....hope this helps|
|08-06-2011 08:33 PM|
Buy a 4.0 and trans and tcase. and swap your body on to it. and the harness
4.0 is better then a 4cyl and you dont have to fab
|08-06-2011 08:00 PM|
|abadoobi||me and my dad did a frame swap on a jeep in my driveway. it was a pain but i was quoted at least 2000 by a shop. it took us about 30 days working 4-5 hours a day during the week and atleast 8 hours a day on the weekends. but we had a million rusty bolts. had to fab some stuff. im sure you will have to also. if your frame is that bad your body mounts on the jeep tub may be going bad also. if this is the case unless you or someone you know can weld it probably wouldnt be worth your time. even if you or somebody else can weld the mounts it may not have good enough metal around to weld to. if your body mounts are good and you have time and another vehicle to drive i would say go for it|
|08-06-2011 07:47 PM|
|stimpy||I would help you but I live to far away. You may even want to grab yourself a welder and a grinder for a few hundred dollars and give it a shot in the meantime. Semper Fi|
|08-06-2011 06:16 PM|
|BalooNY||Damn I'm glad this forum exists. I have a shortage of knowledgeable/non-wimpy friends left in the area (just left active duty with the Marines and am now back home) that would be able to help. What kind of bill might I be looking at from a shop? For either the frame repair in 3 places or frame replacement. Assuming I would be providing the parts for either.|
|08-06-2011 06:09 PM|
|jfbilbro||LOL......if only it were that simple.......you pretty much gonna have to disassemble your jeep and put it back together.....but with the right tools, some new parts(all new bushings and such), some elbow grease, several GOOD friends, and lots of beer.....it can be done|
|08-06-2011 05:55 PM|
|BalooNY||What kind of work are we talking here? Would it be possible to lift the body up off the old chassis (after everything is disconnected, of course) roll the new one underneath it, drop it down, and boom: new jeep frame?|
|08-06-2011 05:31 PM|
|jfbilbro||stimpy's 100% right.....buy it|
|08-06-2011 05:30 PM|
|jfbilbro||550 is a good price even if if won't work with your jeep....but i think it will with a few mods like moving the motor mounts...nothing major.....me, i'd buy it, if just to resell it ....new frames go for 2400.00 or better and then there's the axles and rears.....lot of work involved in replacing the whole frame, tho....|
|08-06-2011 05:29 PM|
The whole thing for only $550 ?
Snatch that up !
|08-06-2011 05:06 PM|
|BalooNY||Just went and looked at the frame the guy is offering. Its a complete rolling chassis with axles, wheels, steering gearbox, linkage, and its in pretty good shape. No rot and little surface rust.|
|08-06-2011 02:52 PM|
Frame Repair Vs. Replace
I have a 94 2.5L with rust/cracks/rot in the frame on 3 of the 4 shackles (See Pics). It looks as though someone had tried to contain the cracks in the front as much as they could, however they didn't do a spectacular job of it. I've seen the AutoRust frame repair kits ($289 for the front two frame pieces from quadratec) and the Davey Geeps (Welcome to DaveyGeeps.com) rear frame wrap kits ($79.99 + tax + $35 shipping). I also have a lead on a 6cyl frame that appears to be in decent shape. The guy is asking $550 for it
1) is the 6cyl frame compatible with my 4cyl?
2) would it be more practical/cost effective to repair the frame with the kits or replace it, factoring in labor? (I'm not a welder)