|10-20-2009 12:02 AM|
The skyjacker TC shifter relocation bracket works very good.
|10-07-2007 06:02 PM|
|doc_floyd||Advance Adapters also makes an adapter that takes the shifter off the body. I had to relieve it a bit to fit around the trunion rod, but it works fine and was not expensive and is now independent of the body.|
|10-07-2007 05:29 PM|
Man, I really thought I had every cost angle covered and addressed on this lift. Forgot about the linkage...Damnit. Every thing I do to this rig requires 3 more things so the first will work right. Damn this disease. BUT, rig is lookin sweet so a slight smile accompanies every complaint. And the wife has no idea about the SYE/DS planned for next year.
|10-07-2007 02:15 PM|
|orange05tj||Just noticed my tcase wont engage. Im going to do the drop linkage right now. When I did the BL, the directions said if installing a mml, I dont need the bracket. I geuss they were wrong.|
|10-07-2007 01:38 PM|
|10-07-2007 11:06 AM|
a motor mount lift would lift the tcase a little closer to the linkage thats on the tub... would also point the tcase rear output shaft downward toward the rear axle pinion and reduce the angle... eliminating the need for a tc drop.
Here is the link to the novak shifter I was talking about:
and here are the instructions for installing it in your jeep:
|10-07-2007 10:51 AM|
|10-07-2007 10:50 AM|
|nregas1||Thanks guys. I like the idea of eliminating the z-linkage but also like the idea of a difinitive shift feel. Do either of you have any specifics on those parts so I'll know I've found the ones you mentioned? Wasn't sure if there were several to choose from? THANKS!|
|10-07-2007 10:46 AM|
|orange05tj||i did the same thing except i took out the tc drop and did the mml, no probs now. Didnt even have to use the tc bracket.|
|10-07-2007 08:47 AM|
|jeeperman||Skyjacker makes a transfer case linkage relocation kit as well. That is what I am using on my Rubicon, and I love it. It eliminates the sloppy rubber body mounts of the stock linkage. Makes it feel like shifting a transmission, works great. I think I bought mine through Quadratec, if I remember correctly.|
|10-07-2007 01:41 AM|
there is a company called Novak that has a good tcase shifter for NP231. the shifter gets rid of the stock z linkage that is mounted to the tub. I bought it but found it wasn't made for the NP241 in the rubicons. Its possible to get it to work but wouldve been alot of hassle so I returned it.
The people I know who have it in their non-rubicon TJs love it though so you might want to check that Novak company out. They said they are working on a new design for the rubicon np241 and I'll buy that one when it becomes available.
Or you could do a 1" motor mount lift... it would most likely correct or better your linkage problem and you could probably get rid of the transfer case drop kit at the same time.
|10-06-2007 11:31 PM|
Tcase linkage solution??
Just installed the 3" lift and left the 1" BL on for the time being to see if I liked it. Had to do the tcase drop due to vibes which are now gone. Problem is the tcase linkage is stretched to the max. The shifter looks like it's a good bump away from kicking into 4H on its own, not to mention trouble staying in 4L. I already have a linkage drop bracket on there that came with the BL but it's not enough. While getting my alignment at 4WP I questioned them on a solution but they had no answers and basically said I'd have to remove the shifter, cut it, and splice weld an extension on it. Although that may work, it just didn't sound like the best approach. What have any of you guys done to solve this so the shifter works as it should? Thanks.