Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Jeep Flares 97

Join Wrangler Forum Today

Thread: Jeep Flares 97 Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-17-2013 08:57 AM
MIZFAN I used rivnuts when I replaced the flares on my 97.
02-17-2013 03:47 AM
jeepwrangler97 For anyone that comes across this, I just used the screw and little plastic block for most of the holes (I believe this was sold separately, but they did not look like the right parts) and for the difficult last hole towards the doors, I used a long bolt so I could leave it in there sticking out from the frame then I put the bolt through the flare and stuck a nut on bolt. I say this because the last bolt was a pain. I could not keep a screw or anything there while I tightened. The hole closest to the door that is used to attach the flare is difficult to get behind, because the frame surrounds the entire area. There were two holes though for the flare, one was factory and the other was carved out by someone, that helped a little by letting my finger and the long bolt get in behind the hole. Now when I say behind the hole I mean within the frame pointing outside. Not trying to sound retarded, but attaching the flare was a pain in the a$$. I think there is a spring nut but no one knew what the heck I was talking about online or at the shop, this was easier.
08-21-2011 10:31 PM
GrassKicker Try a BODY SHOP around your area. You have to have a special tool to install nutserts, I went and had 5 installed. I think they are 5mm nutserts. Good luck!
08-21-2011 03:08 AM
jeepwrangler97 thank you I will definitely give it a try
08-20-2011 11:30 AM
Wesboy Here's some part numbers for those nutserts I found on another thread.

OEM 6504601
Rugged Ridge 11603.1
08-20-2011 07:53 AM
yoopone I got real good at fixing that issue on my 97. Those things you thread the bolts into are called nutserts. I had to replace everone of them on mine, all were shot. It is kind of like putting in a rivet. You do need the right tool to do it though. Simply drill the old nutsert out and press in a new one. I think Quadratec sells the tool then I found a vendor on here to sell me the nutserts. I just searched on "nutsert".
08-20-2011 07:46 AM
jeepwrangler97 Crap as I looked on another page just now I saw what I was looking for, Hopefully
Well Nuts For Signicade, Plasticade Signs - Neoplex will work, only prob is the guy used them on rubicon flares not stock. Stock flares are covering my tires just fine and AZ is more concerned with emissions than the east coast, heard they were extremely strict.
08-20-2011 07:42 AM
Jeep Flares 97

Been looking around and no one knows what the flip I am talking about, but here it goes. I bought a 97 wrangler tj Se and the dude before me treated it worse than I treated my bike when I was 10. Anyways the back two flares were torn off and I bought stock ones to replace the empty space, added bonus it looks a lot better with flares now. Only problem is I can't get the front bolt in on either side of the jeep. It is supposed to bolted close to the doors, but it is in the frame. I can't go under, above, behind, around, ect, it is all blocked by the frame. Can't reuse the old bolts since one side was missing and the other rusted and bent to hell. How can I bolt the front of the flares into the body w/o cutting or paying 50$ for some auto shop to do it in 5 mins. Also the nuts and bolts I bought with the flares did not come with anything I can just shove into a hole and lock. Thank you in advance this is my first jeep, always loved them, and I will figure it all out bit by bit.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 06:23 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC