Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > General Jeep Discussion > Help - cannot remove driveshaft centering ball

Join Wrangler Forum Today


Thread: Help - cannot remove driveshaft centering ball Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-11-2012 10:00 PM
3rdJeepDown I too have angry sparrows emitting from my 06 TJ and need part numbers for the centering ball kit I checked Stu's website and it refered to parts for a 97 is the parts the same for the 06?
09-13-2011 11:12 PM
Alaska TJ Yeah, I had the "cv flange" separated from it's other half. That part separated from it's other half with no problem. Happily, my pin was in good shape. However it was the ball and it's sleeve that I couldn't extract from the CV flange. It was in there very tight and wasn't corroded at all. I took it to the gear shop where I bought my ball centering kit and ujoints. The ended up drilling it out at no charge in about 3 minutes. From there I pounded in the new ball centering kit and got the driveshaft rebuilt and installed in about 10-12 minutes. Good times!
09-13-2011 12:25 AM
olebluetj that's a double cardan driveshaft, i've broken a few, the ball should have come off
with the cv flange, that's what the hand is holding in the pic,try spraying it with
some pb blaster and let it soak for a day then try prying it off, but be careful you
don't damage the pin that the ball is on or you will be buying a new driveshaft
09-12-2011 01:34 PM
Alaska TJ Yes, I had completely disassembled the driveshaft by removing all of the u-joints and taking apart the ball centering assembly as much as I could. The spring and pins fell out easily enough and I removed the seal that holds in the ball centering assembly, but the ball and the sleeve that it rides in remained very well seated in its original home (don't know the name of that part, but you can see it in the attached schematic diagram in the guy's hand). I don't have a photo of the seated ball and sleeve though.

Anyhow, I took it to a shop on Friday that said that I just needed to put a punch into the hole in the ball and crank on it real hard. I don't have a vise to hold it and could never actually get it out. Their service guy was out so they couldn't do it for me right then, but I figured that I would take it in today or tomorrow to have them do it, since I'm having no luck. Is this common? I hadn't read about anybody else having this problem.
09-09-2011 03:22 PM
IslandTJ Odd, once I removed the u joint (one that fits between the transfer case output and DC shaft end) completely, the centering ball easily came off. Don't want to come off patronizing, but you did remove the u joint, yes?
09-09-2011 02:27 PM
Alaska TJ
Help - cannot remove driveshaft centering ball

I've got my front driveshaft disassembled, but I can't remove the centering ball and its "sleeve" from its parent part on the differential (what is that called?)

Stu's off-road suggests that it will probably fall out, but mine is seated pretty well.

Thoughts?

Thanks in advance.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:35 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC