|Today 07:57 PM|
I own one of the new goPro +3 black units and I keep forgetting to put it in photo mode and use the remote and take photos so I can Keep my phone clean and away... I promise I'll do write ups on my aftermarket double radiator thermostatically controlled transmission cooling system :-)
And it's M.A.M.E as in the arcade emulator :-) been a fan since the early days and in a previous life I used to contribute board dumps.
|Today 07:41 PM|
1. Care to do a short writeup on this? I need to do it soon.
2. Mame as in the famous Broadway musical or M.A.M.E. as in Multiple Arcade Machine Emulator?
(I like both. I prefer the latter of the two, however. I used MacMAME for years.)
|Today 07:32 PM|
|Mamefreak||Replaced the badly leaking valve cover gasket with a Fel-Pro one. Took a while and was a pain but it's done and doesn't seem to leak|
|Today 07:16 PM|
|Momamac||Tightened my track bar on the axle end, appears that the 60mph vibes are gone!|
|Today 06:19 PM|
I got some upgraded Spicer U joints, Synergy ball joints, Black Magic pads, Centric Premium rotors and Timken unit bearings about a month ago. I have almost all of the needed tools ready to go, save for a good set of snap ring pliers - and this baby that Brown Santa just dropped off.
I now have the very nice (USA-made) OTC Ball Joint Service Set #7249 with the four-piece Jeep adapter kit, which happens to fit in the plastic case with the full set. NICE!
Daddy is going to be hip deep in TJ front end work about a week from today.
|Today 06:03 PM|
Decided to trim my bumper, works for now
|Today 05:47 PM|
|Today 05:40 PM|
|DJs97TJs||Decided to pull the trigger on a set of 35x14.5r15 nitto mud grapplers and a ford 8.8. Just out of curiosity the guy wants $200 for the whole 8.8 assembly disk to disk. Is this a good price?|
|Today 05:15 PM|
|Today 09:23 AM|
|Today 09:17 AM|
|Today 07:12 AM|
It uses MIDI fuses.....I have inline fuses on everything coming off it too....just to be safe about it.
|Today 06:33 AM|
|ptoncannon||On this bumper I'm building, I need to mount my winch on it, but the frame rails are covered by those boxes i put in yesterday and I posted pics yesterday... The steel is 3/16th inch thick and is mounted very sturdily to the frame. If I were to just mount the winch directly to the bumper, in between the 2 boxes just inside the frame rails would the metal hold up? I was thinking it would just act like a winch plate since it's 3/16th inch but just need to get a second opinion.|
|Today 01:06 AM|
|seeraedave||Tires and wheels.|
|Today 12:51 AM|
Installed couple weeks ago
|Today 12:15 AM|
|Yesterday 11:26 PM|
|Yesterday 10:50 PM|
saw where you guys were talking about terminals and ran across a site with some very nice setups I thought yall might be interested in. I havnt tried any of these though
Battery Terminal Block - Positive - WiringProducts
|Yesterday 10:36 PM|
|Yesterday 09:57 PM|
|WIwrangler||Finished wiring my new light bar and replaced my headlights after one burned out on the way home from work will post pics later|
|Yesterday 09:15 PM|
|moose90||Ok so I bought the jeep 4 months ago and I'm slowly getting there, soo on that note just finished wielding in a floor and painting it for now, have monsterliner in the house I will be doing that soon!! Can't wait, attempted the u-joints today and they we're completely seized on! 😭yay, lol hopefully I can finished them tomorrow will post some pics|
|Yesterday 08:21 PM|
|coolhand||Finished painting roll bars and added some cammo netting.|
|Yesterday 06:03 PM|
|bucksrunner||New floor mats for the jeep today!|
|Yesterday 05:55 PM|
Made some progress on my stinger build today!! Got it fully mounted today and put these boxes on the side for stylistic purposes and to mount the support bar on. Will finish boxing these in tomorrow morning but I'm really liking the way it's turning out.
I think we will put the support bar on next, which we will make out of rectangular tubing and then the stinger will be after that. I just can't wait to finish it!
|Yesterday 05:33 PM|
Decided to upgrade the speakers in the soundbar. Threw in some fiber fill from a pillow I had bought for another speaker project. Sounds pretty good.
|Yesterday 04:15 PM|
Autozone, part# in photo.
|Yesterday 03:58 PM|
|Yesterday 03:47 PM|
|Yesterday 03:24 PM|
So, regarding my ignorant post about this: never mind... ;-)
|Yesterday 03:01 PM|
So don't use a Volvo COS? Use one that goes in the cable...
Simple, removable key and it works great!
|This thread has more than 30 replies. Click here to review the whole thread.|