Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Diff Cover Clearance?

Join Wrangler Forum Today

Thread: Diff Cover Clearance? Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-19-2011 09:18 AM
UnlimitedLJ04 the diff cover will likely not clear the gas tank. you need to check full this by pulling the rear springs and pushing the axle to full suspension compression.

If you can't get here, you need to address your bumpstop extensions so you can:

I know for a fact the Riddler rear D44 will NOT clear in the rear with stock 15.75" LCAs, and stock length uppers. it does rub the gas tank, been there, done that.

Here's a Solid cover at full bump (which is lower profile than a Riddler), with 15.75" lowers and 13.75" uppers and a high clearance savvy gas tank skid:

The first problem is your 16" LCA's. You need to keep those at stock length, or actually shorten them slightly. To adjust pinion angle you need to shorten the lowers slightly while extending the lowers - basically rotating the housing about the hub center, instead of pushing it back.

the next thing you need to do is check the clearance of the track bar bracket at full bump - they can hit the fuel/emissions lines.

the next problem you'll find is the rear track bar hits the frame at the gas tank mount. the relocation bracket, or moving the axle back both create this interference.

the way I fixed these issues was with a high clearance gas tank skid, 15.75" lowers, 13.75" uppers, and a custom track bar. basically a used Rubicon Express track bar with heim end + a stock solid track bar. The stocker was heated up with an oxy-acet torch and bent to fit..and the heim end was sleeved on and welded.

all this because you can't run an adjustable track bar hits the stock bracket and prevents droop. you can't cut that lip off or you'll weaken the bracket significantly. the relocation bracket also fixes the roll center in the rear, so its beneficial.

now that thats want to use a diff cover thats lowest profile. the stock diff cover is the lowest profile. i'd suggest a Barnett/T&J diff cover, or a bolt on skid like Warn or Rugged Ridge. You can also pull a 3/16" thick front D44 cover off any late 1970s Chevy, Dodge or Ford truck.
09-18-2011 08:23 PM
Diff Cover Clearance?

I have a Dana 44 rear in an '01 Sport. 3" lift. I set the lower CAs to 16" and adjusted upper CAs to get 0 degrees pinion angle.

Doesn't look like much clearance between the factory diff cover and factory gas tank skid. Maybe 1/4" to 1/2".

What is a strong diff cover that will clear? I sure like the cast ones that have a smooth transition to the carrier like a Riddler, but not sure how much further it sticks out than the factory cover.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 07:29 AM.

Jeep, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC