Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Ventilation

Join Wrangler Forum Today


Thread: Ventilation Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-07-2011 12:59 PM
Katman19 [QUOTE="Katman19"]Thx Old Grunt. I started simple like you suggested and bought a new knob for the vent control. The old one was worn and the plastic slightly cracked that holds the metal insert. Now I can successfully navigate as to where I want the air to blow. There is, however, a slight delay in the air to switch vents when directed. I can live with that considering the alternative sounds a whole lot more complicated. I hope it lasts. Thanks again for all the responses. /QUOTE]
11-07-2011 12:57 PM
Katman19 Thx Old Grunt. I started simple like you suggested and bought a new knob for the vent control. The old one was worn and the plastic slightly cracked that holds the metal insert. Now I can successfully navigate as to where I want the air to blow. There is, however, a slight delay in the air to switch vents when directed. I can live with that considering the alternative sounds a whole lot more complicated. I hope it lasts. Thanks again.
10-09-2011 11:21 AM
Old Grunt I hate to say it but its both the switch (which is a piece of crap to begin with) and the HVAC system itself. The switch is one of those dial type's. Eventually after time goes on, the switch's contact's wear down and the rotary contact's start 'skipping'. Ergo, the HVAC goes wacko ! The only real solution is to replace the whole switch (and buy a couple of extra's. You'll need them if you're going to keep the Jeep for any length of time) which is fairly straightforward. Disconnect the battery, strip the center console of the rotary knob's and ashtray and unscrew the whole dammed thing. it looks overwhelming but take it 1 step at a time, and even get some help if you can, and it will come out. The switch itself is a 2 screw 'hold-down' and comes out pretty easy. Just be sure you unplug the electrical contact's first ! A fast spray of contact cleaner wouldn't be a bad idea either given what Jeep cab's tend to collect ! The install is in reverse order. Once you're all buttoned up, put the TEMP to whatever and run the fan speed switch thru all 4 setting to be sure the switch is installed right.

The other problem is, unfortunately a lot harder to solve. There is a HVAC selector rod that control's the defroster duct's that is a real 4 star PITA ! It requires you to almost totally strip the dashboard, including the gauge cluster, out to get to it. Jeep Magazine covered this and they were quoted (bear in mind they're in California) a completed shop price of over $1000,-- to do this one.

Once you get to it, it's a simple matter to slide the end of the HVAC control rod back into the defroster control lever. The problem is that the arm just sits in the arm's drilled out hole WITH NO MEANS OF KEEPING IT PINNED IN !. This was covered about a year ago, best I can recall, in JEEP Magazine. Everytime they had their test Jeep go out and trail ride, even on simple sand dunes, the rod would 'pop' out. JEEP Mag's solution was to take the rod out, put it in a drill press vice and drill a small hole in the end of the rod, beyond where it sit's in the hole and insert a cotter pin to keep it from coming out no matter how bumpy the ride. Not a bad idea when you think about it.
10-09-2011 10:37 AM
InfernoGirl Yes there is a fix, it's a common problem. Unfortunately I can't recall at the moment the correct terminology to help you search for it. Try googling blower switch Wrangler forum or similar. Lots of times google search is more effective than the search engine on the forum itself.
10-09-2011 10:10 AM
Katman19
Quote:
Originally Posted by Katman19
My vent/ac control knob doesn't always blow air to the vent selected. For example: if knob is dialed to dash vents, partial air will blow dash and strong air at feet. Is there a fix?
Ok thx.
10-09-2011 09:54 AM
Mikekaz1 Sorry no help really from me. But my dads ram does that too. I'm guessing if it's just electrical from the switch then you could just swap out for a junker one. But idk if it would be more of a inner louvre problem.
10-09-2011 09:51 AM
Katman19
Ventilation

My vent/ac control knob doesn't always blow air to the vent selected. For example: if knob is dialed to dash vents, partial air will blow dash and strong air at feet. Is there a fix?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:19 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC