Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Poison Spyder JK Evap Skid Plate Install

Join Wrangler Forum Today


Thread: Poison Spyder JK Evap Skid Plate Install Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-09-2011 09:55 PM
mastenp
Quote:
Originally Posted by TroutSafari View Post
The underside of your jeep is very clean. It must be a pleasure to work on.
It was a pleasure. Have been super busy at work and only purchased the Jeep 2 months ago. Plus its either been super hot around here lately. I plan on getting out with some friends soon.
10-09-2011 09:29 PM
daggo66 I strongly recommend the Skid Row evap skid plate. Very easy to install and it doesn't require removing the cannister.
10-09-2011 09:10 PM
mastenp
Quote:
Originally Posted by TroutSafari View Post
The underside of your jeep is very clean. It must be a pleasure to work on.
It was a pleasure. Have been super busy at work and only purchased the Jeep 2 months ago. Plus its either been super hot around here lately. I plan on getting out with some friends soon.
10-09-2011 09:03 PM
TroutSafari The underside of your jeep is very clean. It must be a pleasure to work on.
10-09-2011 07:22 PM
isitme Very cool! I was just looking at these.
10-09-2011 07:18 PM
kjeeper10
Quote:
Originally Posted by mastenp
This weekend I installed the JK Evap Skid Plate from Poison Spyder on my 2011 JKU. Sorry for not taking pics along the way.

Upon arriving at my house the box was pretty chewed up and mangled, but everything was packed well and there was no damage to any of the parts. The kit comes with the skid plate, a back plate, a top strap, mounting hardware and instructions. The instructions list most of the tools needed for the install although a flat head screw driver is not listed but is needed to remove the stock mounting bracket once you have the evap canister off the vehicle. Also I didn't have a 16mm open wrench, so I used a 5/8ths and it worked just fine.

After unplugging both of the connectors from the back of the evap canister, I attempted to remove the evap line but was unable. So I decided to try the install without removing the evap line. Everything went smooth following the included instructions until I got to the part where you need to mount the skid plate with the front two factory bolts. This would be much easier to do with a second person and possible even easier if you jack up the Jeep. I have a stock suspension and just crawled under my Jeep. After trying to get the first bolt finger tight through the wrench slot in the front of the skid plate I decided to try and reach my left arm from the rear inside the skid plate, while holding the skid plate with my right arm. This made getting the first two bolts finger tight much easier. I was then able to slide the evap canister with the evap line still attached into the skid plate and complete the install without any further problems.

Make sure to read the instructions carefully, as I didn't and initially installed the back plate on the outside of the skid plate, then re-read the instructions when the rear factory mounting hole didn't line up. So I had to go back and remove the three screws that hold the back plate in place and re-install the back plate correctly.

Overall a very easy install that took me 1 1/2 hours. Would have been much faster without my mistake on the back plate installation. You could also cut down on time with a second set of hands and if you have a lifted Jeep, or jack it up a bit.
That looks awesome.
10-09-2011 07:04 PM
mastenp
Poison Spyder JK Evap Skid Plate Install

This weekend I installed the JK Evap Skid Plate from Poison Spyder on my 2011 JKU. Sorry for not taking pics along the way.

Upon arriving at my house the box was pretty chewed up and mangled, but everything was packed well and there was no damage to any of the parts. The kit comes with the skid plate, a back plate, a top strap, mounting hardware and instructions. The instructions list most of the tools needed for the install although a flat head screw driver is not listed but is needed to remove the stock mounting bracket once you have the evap canister off the vehicle. Also I didn't have a 16mm open wrench, so I used a 5/8ths and it worked just fine.

After unplugging both of the connectors from the back of the evap canister, I attempted to remove the evap line but was unable. So I decided to try the install without removing the evap line. Everything went smooth following the included instructions until I got to the part where you need to mount the skid plate with the front two factory bolts. This would be much easier to do with a second person and possible even easier if you jack up the Jeep. I have a stock suspension and just crawled under my Jeep. After trying to get the first bolt finger tight through the wrench slot in the front of the skid plate I decided to try and reach my left arm from the rear inside the skid plate, while holding the skid plate with my right arm. This made getting the first two bolts finger tight much easier. I was then able to slide the evap canister with the evap line still attached into the skid plate and complete the install without any further problems.

Make sure to read the instructions carefully, as I didn't and initially installed the back plate on the outside of the skid plate, then re-read the instructions when the rear factory mounting hole didn't line up. So I had to go back and remove the three screws that hold the back plate in place and re-install the back plate correctly.

Overall a very easy install that took me 1 1/2 hours. Would have been much faster without my mistake on the back plate installation. You could also cut down on time with a second set of hands and if you have a lifted Jeep, or jack it up a bit.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:29 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC