Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > 95 YJ missing / power loss

Join Wrangler Forum Today

Thread: 95 YJ missing / power loss Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-11-2011 09:25 AM
sevenservices Could a clogged fuel injector cause this?

it could... I had it happen in a ranger. I had to pull each spark plug wire off with a glove until I found a cylinder that did not change the way it was running. That was my bum cylinder. It was bone dry inside and on the plug.

When that one was running it felt like sitting in a helicopter. It was horrible... new injector and away she went! Although, these may only have a fuel injected throttle body. Not sure that you have an injector at each cylinder?
10-11-2011 09:12 AM
k2keith Here is the update on what I tried last night.
1) I ran it in the dark, no visible ignition system shorts
2) I double checked the timing, first by find TDC on 1, then checking it against the rotor cap, they match, it is not 180 degrees off
3) Next I double checked the timing with a timing light, I am about 8 degree off of 0, it does move slightly, but it is roughly about 8 degrees off.
4) I pulled the air cleaner hose from the throttle body, it seemed to help slightly.
5) Following the lead that it may be struggling for air, I removed the elbow and hose that goes to the back top of the valve cover, no difference.
6) I removed that small hose that goes on the front drivers side just below the valve cover, something similar to a PCV valve if I understand it right. that seemed to improve things more, it smoothed out a bit. When I put my finger over the hose it bogged down heavily.

Is there something else I should consider and test? Could a bad coil cause this?

You cannot turn the distributor to change the timing so what electronically controls the timing? I read that the 1995 4 cylinder models don't have an ECM. Is there something else I should check there?

I need to try the compression test, I have never done that before and don't have a good understanding of that process. I will read up on that.

Could a clogged fuel injector cause this?
10-10-2011 07:29 PM
Jeep716 I would compression test each cylinder. Pull valve cover and watch movement on the rockers. You may have rounded off a few lobes on the cam and valves aren't opening fully on the two cylinders giving you issues. Good luck. Mine just hit 205k so I feel your pain.
10-10-2011 04:33 PM
sevenservices choke stuck? I don't know how these particular engines control their choke but man, sure sounds like way to much gas and that would be one way to get it.

Or, obstruction in the air intake such as a mouse nest??? Pull your air cleaner hose off from the throttle body and try it. If it smooths out, something is choking your air intake. ...just an idea of the first places I would check.
10-10-2011 03:57 PM
quadrophine i would double check the timing... try running it in the dark, mine was behaving like that not too long ago. i changed the plugs out after i realized one of the plugs were shorting on the block. I imagine you may have a short somewhere in the distributor. try running it in the dark and see if you see any light coming from in or around the ignition system.
10-10-2011 02:18 PM
k2keith Thanks for the any help!
-No serious oil leaks (down less than 1/4 quart in 3000miles)
-Using valvoline high milage synthetic blend oil
-Mileage is ~ 156000
-New plugs were put in for the tuneup when this problem started, I did not get it running well, and pulled them when I changed the timing chain and gears, #2 & 3 were fould by then, less than 5 minutes of running. they were gassy smelling and black, not oily though.
-Firing order is correct from what I can see from the haynes manual, and we changed the plugs and wires one by one to try to avoid any mixup.
10-10-2011 12:05 PM
EMTJEEP Are you leaking oil anywhere? What kind of oil are you using? How many miles are on it? How long where the plugs in till they fouled out. That could be because you're running to rich. Are they oily or gassy smelling when you checked them? There could be a leak letting too much oil/gas in. Are your firing orders right?

I got some ideas but need some more info from you.
10-10-2011 11:05 AM
95 YJ missing / power loss

Hey, I am new here, but have been browsing the forum for quite some time now. I finally have a problem I can't figure or find a clean answer on the forum.

95 YJ 4cyl lots of miles, fairly rough truck, bought it really cheap a year or so ago.

Ran okay, other than a lot of ticking common for these older engines. The oil pressure consistantly reads low and has for the last year I have owned this jeep. Low meaning just above the peg at the bottom end of the gauge.

The jeep began to stumble and lose power one day when my daugher was out in it, at first just at stops, then progressively worse. It got so bad, she called me and pulled it over.

We drug it home and have since done the following:
Tune-up - plugs, wires, cap & rotor, air filter
Fuel Filter
Timing chain and gears

It continues to run VERY rough from the minute you start it and it never smoothes, I suspect 1 or 2 cylinders are not firing. If you try to drive it, 35 mph max maybe if you work at it, gassy smell under the hood, traces of smoke occassionally out of the exhaust. I pulled the new plugs, and 2 of the 4 (# 2 & 3) were already black and fouled.

It is not throwing any check engine lights, but that may be because it does not work or exist on this truck.

I have dealt with rough running on other jeeps, such as replacing IAC etc, but this is much rougher, shakes the heck out of the jeep.

Any wisdom, I suspect perhaps the engine is shot, but hoping for something less expensive.

Thanks for any wisdom,

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 03:11 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC