Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > gearing question

Join Wrangler Forum Today


Thread: gearing question Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-26-2011 12:16 AM
TJWenatchee I just bought the bullet and had everything replaced including an upgrade to 4.56 gears but yet still running a narrower tire at 33x10.5x15. But, with the 4.56 gears and the 15x8 Cragers I could in the future run 33x12.50.
10-25-2011 09:15 PM
TJ.jim i agree, ive been tinkering with it and the wire wheel and it is cleaning up. i just want to explore my options.

thank for the advice!!
10-25-2011 08:54 PM
Jerry Bransford An axle that is rusty on the exterior is normally fine inside. A wire wheel, a little elbow grease and satin black Krylon or Rustoleum, and I'm betting it will look pretty enough to make you want to install it. Unless you're already well versed in installing R&P gearsets, you really don't want to try swapping those used gears into your axle. A mechanic will often even charge more to installed used gears because they are harder/more time consuming to install.
10-25-2011 08:52 PM
TJ.jim that was my original plan, but the '98 axles i picked up turned out to be in alittle rustier then i wanted and just plain old beat.

i personally wouldnt be doing the work. i have a mechanic that does work on the side. he set up the gears in my last truck.

so, even though you wouldnt recommend just swapping the guts, i can be done.
10-25-2011 08:44 PM
Jerry Bransford Swap the axles, don't swap the gears between the axles. New gears have a tedious setup process, used gears are even harder to set up since they already have work-hardened areas on the gear faces that would need to be matched up to. You'll spend less time swapping the axles than it would take to swap the gears even if you knew how to set gears up. Not to mention the present gears are happy how they are set up now.
10-25-2011 08:43 PM
TJ.jim i think im leaning towards 32's.

i should also note this tj will be daily driven about 30 miles a day.
10-25-2011 08:37 PM
nick50471 32's is as big as I'd go on 4.11's. Lots of folks on WF are running 33's.
10-25-2011 08:35 PM
TJ.jim manual
10-25-2011 08:34 PM
nick50471 You would have to swap both ring and pinion gears. They are matched.

Manual or auto tranny?
10-25-2011 08:31 PM
TJ.jim
gearing question

i bought a d30/35 off of a '98 tj with 4.11s in it. can i just swap the guts into my '03 tj axles (currently housing 3.07s) or do i need to swap the entire assemblies?

also, what is the 'ideal' tire size for 4.11s in a 4.0?

thanks everyone!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 06:49 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC