Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > 1997 Jeep Wrangler Fog Light HELP!!

Join Wrangler Forum Today


Thread: 1997 Jeep Wrangler Fog Light HELP!! Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-24-2011 07:00 AM
z250kid Sorry to bring up an old thread. But i have this in my 1997 wrangler and i have the light blue wire going to the turn signal harness which plugs into the headlight harness. Now it does have the fog light wire on the turn signal harness but i found a harness that does. My question is will this work now?
12-21-2007 11:17 AM
bpav
Quote:
Originally Posted by erickpl View Post
But what fun is THAT? hehehe

I have a PDF of the wiring setup I did in mine. It is pretty much step by step, with pics and lots of dialog to walk you through it. PM me if you want a copy I can email to you. It's a 924Kb file, so I hope you don't have dialup.
That would be great! Please send the PDF... you are a life saver! T

Thanks to everybody for your posts. Obviously, I'm new to the forum... I really like it. I've only had my jeep since August, so hopefully I can contibute some good advice too someday!
12-19-2007 10:43 AM
erickpl But what fun is THAT? hehehe

I have a PDF of the wiring setup I did in mine. It is pretty much step by step, with pics and lots of dialog to walk you through it. PM me if you want a copy I can email to you. It's a 924Kb file, so I hope you don't have dialup.
12-19-2007 10:42 AM
Walkeraviator IN mine, the wires go through the grommet beside the steering column and are spliced into a wiring harness i got from Jeepsareus (prolly same as yoru fatory harness).
12-19-2007 10:41 AM
Walkeraviator www.jeepsareus.com sells the entire wiring kit for the fatory lights. Relay and all. They have really well written instructions as well. Thats how i did mine 3 or 4 years ago.
12-19-2007 10:21 AM
erickpl
Quote:
Originally Posted by bpav View Post
Well, I guess that's what I'm asking. If somebody has a diagram, that would be helpfull. I would know what to do if I had a diagram. Either that, or maybe sombody has experience tracking those specific wires and know where they lead?? Verbal direction is also welcome!!
Also, you CAN buy fog wiring kits for fogs from most major car parts stores, and I've even seen em at WalMart. They are easy to hook up, but I just don't like the thin wire they used.

When I hooked up my rear fogs, the 'kit' I wanted to use with the lights I got was REALLY thin wire and I had to do a few splices to get the longer length I needed. That told me I really needed to run a custom setup so ran it all myself.

I have a writeup here that covers how I did it. Just search for 2nd switch bezel and it covers a lot of it.
12-19-2007 10:19 AM
erickpl Run postive wires from fogs to relay.
Run negative wires from fogs to ground (I grounded to ground on relay).
Run wire from lead on relay to battery (I fused it too).
Run wire from lead on relay to switch.

For switch,
Connect wire from relay to proper lead on switch
Connect ground to a ground
If you have illuminated switches, run wire from proper lead to switched source (over by glovebox works fine)
If you have illuminated switches for when dash lights are on, run lead to orange wires in dash (I tapped of wire for HVAC illumination just above it).
12-18-2007 01:36 PM
bpav
Quote:
Originally Posted by 02Prove View Post
It may be easier to start over and run the wires from light to switch than to try to tap into the factory harness. Unless you have a diagram or know what you are looking at.
Well, I guess that's what I'm asking. If somebody has a diagram, that would be helpfull. I would know what to do if I had a diagram. Either that, or maybe sombody has experience tracking those specific wires and know where they lead?? Verbal direction is also welcome!!
12-18-2007 12:21 PM
02Prove It may be easier to start over and run the wires from light to switch than to try to tap into the factory harness. Unless you have a diagram or know what you are looking at.
12-18-2007 12:14 PM
bpav That's a very nice set up! I am very enveous, that's for sure! I've only had my Jeep since August 2007.. So it's gonna take some time to get it up to par, where I want it!!!

I don't think I have the wiring through my fenders, but I don't mind trying to run wires, as factory intent. What I don't know is where I'm suppose to run those wires to. Starting at the light end... I can feed the wires through, but where do I hook them up to tap in to that factory wire harness behind the blank? Maybe I'm supposed to go to the fuse box somewhere?
12-18-2007 10:59 AM
dwdrums801 yea in my 99 i had the wiring behind the blank also but no wireing for the lights themselfs in the fenders
12-18-2007 10:57 AM
erickpl Do you have the pigtails hanging under the fenders in front ready to hook up? If so, just plug em in.

If not, you may have to run wiring yourself. My 97 SE didn't have the wiring, but it DID have wiring behind the blanks for a foglamp switch. I chose not to use it since I didn't have any other wiring.

I ran custom wiring to a relay, the battery, and a switch that was just like my ARB switches. This way, they all looked alike.

This is a diagram I saved off another forum that shows the pinouts for a factory switch. BTW, you can get the ARB-style switches (made by Carling Contura) from www.otrattw.com and have it with a label on the front for about 11.00 (roughly).



You can see my switch setup here.

12-17-2007 04:07 PM
bpav Sorry.. I had a type-O in the head. My Wrangler is a 1999!
Thanks!
12-17-2007 03:45 PM
bpav
1997 Jeep Wrangler Fog Light HELP!!

OK... so I'm trying to install fog lamps. There is a blank next to my cigarette lighter where the fog light switch should go. I pulled the blank and found that there is a wire harness installed, ready for the switch. I've located the switch for installation and can hook up the switch with no problems. BUT, I'm not sure where the wires lead to or how to wire the light from there. Can anybody tell me where the fog light wire harness leads to? I need to know how to tap in to it on the "lighting" end of it.

anybody have a wire diagram for it?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:11 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC