Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > That awful tubrust...

Join Wrangler Forum Today

Thread: That awful tubrust... Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-28-2011 08:41 PM
KneesCollapsing As far as body rust I really have very little, a few specs on the tailgate and on my windshield/door hinges that I'm working on treating because compared to most Jeeps I see around mine is in really nice shape for being an 03 so I'm trying to catch everything I can. Rust chasing is like you said never ending.
11-28-2011 08:31 PM
doolyd I just started doing the same and my plan is to coat just the front of the tub with rust-oleum and then the rattle can truck bed liner. I was going to do the entire tub but there is no rust any where and the only slight rust I found was the drain holes under the rubber stoppers in the front...nothing like what you have here.

I have to give you guys props for doing the entire is a lot of work, not hard but tedious. Chasing rust is a never ending battle and my jeep, for being a 97, is in real good shape so I am going to stop chasing it.
11-28-2011 08:15 PM
Dgrimjeeper I've tended to use an anti rust inhibitor called rust bullet. I use it on my ancient 79 Cherokee and have had great results with it. It takes a couple of coats (and yes you have to grind down or scrape off the rust flakes first) but overall I've been very happy with the results. It smells like no other though, so you'll have to have a well ventilated garage or apply it in the open air otherwise you might end up reenacting a Cheech and Chong film...

I've really enjoyed the results I've gotten from it....

Rust Inhibitor Paint | Stop Rust | Rust Corrosion Inhibitor | Rust Converter
11-28-2011 07:49 PM
KneesCollapsing I started doing some under body and frame grinding today to clean up some rust you can see from a standing view, but I dont think I'm going to do too much because I live in Buffalo and things like my axles, drive shaft and exhaust show no sign of ever being not covered in rust. We'll see, little steps at a time.
11-28-2011 05:34 PM
WaterDR It would seem the more prep work and pricey a product is, the better the results. No free lunch.
11-28-2011 02:23 PM
Peepers I used por15 on my frame last winter. I recently had a brake line go right above the frame. ate right through the top coat, but didn't scratch the por15. Thats some tough stuff.
11-28-2011 02:11 PM
The other stuff?

Any thoughts on the difference POR15 and other products like Chassis Saver and Rust Encapsulator in terms of effectiveness and ease of application?
11-28-2011 12:17 AM
topher38 now that your rust looks like its gone. go get a good spray in liner to cover it up and it should do the trick for that crappy rust =)
11-28-2011 12:10 AM
KneesCollapsing After applying rust treatment, and then with a first coat of paint. I'm hoping that's the last of the rust I'll be seeing.
11-27-2011 11:36 AM
WaterDR I wonder how it got there then. Makes a good point about periodically removing to dry up.
11-27-2011 11:14 AM
KneesCollapsing Yeah they're lipped and molded to fit the tub, the moisture was only under the mats so that's what prevented it from drying and caused the rust
11-27-2011 12:40 AM
WaterDR Do you have the kind with the lip?

Previous owner had flat ones and carpet was wet all winter.
11-26-2011 09:15 PM
KneesCollapsing I use the quadratec super heavy duty mats and i guess I trapped moisture under them and rotted my pans right out, now the trouble is finding the source of moisture...
11-26-2011 07:03 PM
WaterDR Mine looked just like this!!!

I hit both sides with a wire brush wire wheel and POR 15. I used the degreaser and the etch ore product. Pain in the ass.

Frankly, hitting it with rustoleum primer and topper is probably nearly as good for less cost and effort. Mine took 12 years to get rusty, I bet it will last another 12 with rustoleum though probably last forever with POR.

Had me and the previous owner used good rubber mats, the rust would never have been there in the first place.
11-26-2011 05:51 PM
KneesCollapsing Of all the hardware stores I called I couldn't grab any por15 today so is went with another brand because this is urgent so we'll see how it works and if I need something stronger I'll order some online
11-26-2011 01:32 PM
Wallygator As much as you can. Then use the metal ready prep. then have at it.
11-26-2011 11:01 AM
KneesCollapsing Do I need to remove all rust in my tub before applying?
11-26-2011 10:56 AM
Wallygator Its a serious product. And really the best way to go. Stuff is tuff as hell and will last forever and take all kinds of abuse if applied properly. Guys use it on roll bars bush bars, and boat racks and years later they still look great.
11-26-2011 10:49 AM
KneesCollapsing Wow this stuff has some serious directions
11-26-2011 09:10 AM
TnDz TJ POR15 is the way to go, but the prep is key... follow to the letter of the law...
11-26-2011 08:20 AM
thejackcutts Wire brush the crap out of it and use rustoleum or the better, POR15. That takes a lot of prep and work. But it is your tub and specifically your floor pan.
here is their link to quick directions if you wanna take a look.
11-26-2011 01:10 AM
That awful tubrust...

What's the best way to treat this tub rust? I just noticed how bad it has somehow become when I pulled my heavy rubber molded mats up and found the moisture. I steel brushed some and my next move was grinding and then bedlining, is there a better way to go about this? What's involved in using Por15?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 03:28 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC