Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > Community Forums > WF New Member Check In > Help with 88 Wrangler not staying running

Join Wrangler Forum Today


Thread: Help with 88 Wrangler not staying running Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-05-2011 08:52 AM
1SAS Jimmie,

The muffler could also be plugged. Did you do the vacuum test as mentioned above to check for back pressure? How do you know the fuel pump is stopping operation? Is it shutting off? What kind of engine do you have?

Take care,
12-04-2011 01:58 PM
Jimmie We took the tank down and cleaned it while we were replacing the fuel pump. We have also by passed the Cadalitic converter. That didnt help either. Any other Ideas?

It seam that the fuel pump is stopping operation or it is not being told to keep pumping. It just stops putting fluid to the injector and the Throttleboddy
12-03-2011 07:53 PM
Ageless Stranger Welcome to WF.
12-02-2011 03:37 PM
Beastmaster Hello!
And Welcome to the Forum!

(BTW, have you flushed your gas tank? there may be gunk in there)
12-02-2011 06:32 AM
DarthJeep Welcome to WF. Don't forget to Wave.
12-02-2011 04:24 AM
blkrubi88 Welcome!
12-01-2011 11:11 PM
1SAS If you replaced the fuel pump and filter, we can "rules those out" for the moment. I would check exhaust back pressure. Maybe your catalytic convertor is broke, clogged, blocked, etc. The way you check it is with a vacuum gauge. The directions follow:

Using a vacuum gauge to check back pressure...

Connect the vacuum gauge to a good port on the intake manifold. If you think you may have a "back pressure" issue, get the vehicle at normal operating temperature and slowly bring engine to 2,000 rpms. Close throttle quickly. If no back pressure is present, the pointer will jump past your normal reading and smoothly return to normal, just as fast. If it is slow or uneven return, there is an issue of back pressure. You can also test it another way… hold the engine at 2,000 rpms and watch needle. If it begins to decrease gradually instead of holding steady, there is an exhaust restriction somewhere.
12-01-2011 10:38 PM
Jimmie
Help with 88 Wrangler not staying running

I have an 88 Wrangler YJ. It will not stay running after it has been running about 15-20 minutes it starts to starve for gas. I will idle fine for as long as you leave it alone. I have replaced the following. (plugs, wires, distibutor cap, rotor cap, even the fuel filter and then the pump) it runs alot better but still seams to lack power and does not seem to have enough gas going to the throttle body. Does anyone have any ideas on what I am missing?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:35 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC