Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > 97 jeep wrangler tj injector issue

Join Wrangler Forum Today

Thread: 97 jeep wrangler tj injector issue Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-14-2011 04:10 PM
Negat Corpen okay so i bought a new crank position sernsor didnt fix the problem now i am getting that codes 31 and 42 the evap solienod makes a surge sound like short cicuit when i turn the car on what does that mean and 42 is a short or something in the asd i dont know where to even start
12-10-2011 04:33 PM
Jerry Bransford
Originally Posted by Negat Corpen View Post
ya it was 0 nothing at all
I still don't know what you mean by that. 0 as in 0 resistance (dead short) or 0 as in 0 connection (open, no connection at all).
12-09-2011 03:25 PM
Negat Corpen ya it was 0 nothing at all i even took the sensor out and checked on the other side of my solder and still nothing
12-09-2011 03:24 PM
Negat Corpen i oredred a new one and thanks ill let you know if it starts when the part comes in
12-09-2011 03:16 PM
Jerry Bransford 0 as in a dead short with 0 Ohms (no resistance at all), or 0 as in no connection across it whatsoever?
12-09-2011 02:55 PM
Negat Corpen it had no reading it read 0
12-09-2011 02:26 PM
Jerry Bransford Place an ohmmeter across terminals B and C. Ohmmeter should be set to 1K-to-10K scale for this test. The meter reading should be open (high resistance). Replace the sensor if a low resistance is indicated.

That is right out of the '97 FSM.
12-09-2011 02:21 PM
Negat Corpen it melted before the motor blew up then we fixed it and it ran fine i checked for power at the crank position sensor andc there was 5 volts
12-09-2011 02:17 PM
Jerry Bransford Since the crankshaft position sensor wiring melted to the header, it's possible that shorted its power to ground and that circuit is now dead. I'd check for power on the CPS wiring and start tracing back if there is no voltage on it. Might be as simple as a blown fuse.
12-09-2011 02:10 PM
Negat Corpen the thing is i have spark to all my cyclinders my dad put a header on it and it melted the wires to the crank sensor so we butt connected the wires back together but know that i had the motor out i soldered the wires and heat shrink them could that cause problems
12-09-2011 02:08 PM
Jerry Bransford The ground is indeed supposed to pulse, as is the ground for the ignition coil. I'd be suspicious of something like the crankshaft position sensor not working which the PCM requires before it will enable the ignition and fuel injection systems. If the PCM isn't happy with all of its various inputs it monitors, it won't enable the fuel injectors or ignition system. Check the camshaft position sensor too if the crankshaft position sensor is good. If the ASD (auto shut down) relay is not enabled by the PCM, nothing like the fuel injectors and ignition system will work, it is the ASD relay that controls them and it is controlled by the PCM.
12-09-2011 02:00 PM
Negat Corpen
97 jeep wrangler tj injector issue

I am new to this but here is my problem if you can help. I put a new engine in my 97 jeep 2.5 and now the injectors wont pulse i have checked grounds, relays, also power to the injectors the wierd parts is if i turn the key on and hook a volt meter from the battery positive to the black and green wire on the number 1 injector i get 12v. it doesnt sound right because i thought ground was supposed to pulse.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 04:34 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC