Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Installed new lift, U joint + exhaust problems

Join Wrangler Forum Today


Thread: Installed new lift, U joint + exhaust problems Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-09-2011 09:58 PM
TnDz TJ True.... 3-4" lift should be 3/4". We did this to 06 rubi with 4" lift and was perfect. Every jeep is different, so it's not exact. Sorry for the confusion.
12-09-2011 08:44 PM
DevilDogDoc ^^ not exactly right. The amount varies depending on the height you raised it and how much the axle shifted over.
12-09-2011 08:28 PM
TnDz TJ 3/4" is the magic number for the redrill.....
12-09-2011 07:07 PM
coors yeah you were suppose to move it over 3/4 of a inch
12-09-2011 06:17 PM
DevilDogDoc Thats the problem with the lower end lift kits, they can be incomplete. Do this before you do anything else. Disconnect the tracbar at the axle. Bounce the bumper up and down a few times to center it. See if the clearance improves between your exhaust and driveshaft. If it does then you need to decide on whether you drill the bracket to where it is now or get an adjustable trac bar.
12-09-2011 05:41 PM
BackCountryMud It only came with one for the rear.
12-08-2011 10:19 PM
s14sh3r I looked at the instructions for the RC 3.25 lift and it comes with a track bar bracket. If you didn't install it, DevilDogDoc is right, your axle will be off center.
12-08-2011 09:14 PM
DevilDogDoc Well some kits have you re drill the mount hole on the axle to move the tracbar and recenter the axle. Or get an adjustable tracbar and set it. That said, mine has been offset for a couple of years with no issues but that exhaust repair of yours adds another variable that might be the problem.
12-08-2011 08:36 PM
BackCountryMud No i didn't change anything with the trac bar, was i supposed to?
12-08-2011 08:30 PM
DevilDogDoc Unless it hit before the lift, your axle shifted over which is why things are hitting. Did you do anything to your track bar up front when you lifted?
12-08-2011 08:23 PM
BackCountryMud Do you mean pry between the frame and the exhaust?
12-07-2011 10:49 PM
svtkev
Lol nice!!
12-07-2011 09:57 PM
s14sh3r Here's a really crappy diagram of what I'm suggesting:



From the pictures, it looks like they didn't get the exhaust straight when they welded that new piece in. What I would do is find a small block of wood, a small piece of 2x4 would be great, or use whatever you have handy. Pull the exhaust away from the u joint enough to put the block between where it's hitting the exhaust and the u joint.

This is assuming the new piece is toward the front, which I've indicated with the red circle. When you have the exhaust blocked away from the u joint, use a pry bar, tire iron, small piece of pipe, or whatever... and pry the exhaust pipe toward the driveshaft. When you take the block out, the pipe will be bent away from the u joint. Don't pry very much at one time. Pull the block out and check if you have to. Make sure by bending the exhaust away from the u joint, the pipe isn't hitting somewhere else.

Hopefully that made sense.
12-07-2011 09:31 PM
BackCountryMud Ill try it! ill upload more picks of all the spacing and stuff as far as the exhaust spacing between other parts this weekend when im gonna decide what to do.
12-07-2011 09:27 PM
s14sh3r Look at it and see if there's room for the spot where it's hitting to move over a little. If there is, a pry bar of some sort + a couple of small wooden blocks and you should be able to bend the exhaust and get it away from the u joint.
12-07-2011 09:26 PM
BackCountryMud It's pretty damn close WITHOUT articulating, it's spinning within about a quarter inch of the pipe, not sure why it moves, only notice is while turning right as well.
12-07-2011 09:23 PM
BackCountryMud It's pretty solid. can't hardly move it with your hand.
12-07-2011 09:22 PM
s14sh3r Is the exhaust loose? It shouldn't be solid, but it shouldn't move around very much either. You may be able to tweak it enough with a pry bar to keep it from hitting.
12-07-2011 09:15 PM
BackCountryMud bump
12-07-2011 08:19 PM
BackCountryMud
Installed new lift, U joint + exhaust problems

I installed the RC 3.25 suspension lift last week and my front U joint is hitting my exhaust when i turn right if the body flexes, even on the road or turning into driveways. It appears someone did an exhause repair and put a spacer in and moved the pipe forwards, here's some pics of the spacer first, next to the front control arm.Attachment 81980

Attachment 81981
Next here's some pics of the exhause and U joint, notice the dark space on the exhaust, thats a dent . The picture where you can see the tan carhart jacket is from above.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:35 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC